This step by step diy woodworking project is about a 14×14 outdoor pavilion plans. I have designed this square pavilion with a gable roof so you can create some nice shade in your garden. Make sure you take a look over the local building codes, so you comply with the regulations. Take a look over the rest of our woodworking plans, if you want to get more building inspiration.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.
Projects made from these plans
14×14 Pavilion – Free DIY Plans
- A – 4 pieces of 6×6 lumber – 132″ long POSTS
- B – 2 pieces of 6×6 lumber – 168″ long, 2 pieces – 192″ long TOP PLATES
- C – 8 pieces of 6×6 lumber – 48″ long BRACES
- D – 2 pieces of 6×6 lumber – 36″ long, 1 piece – 192″ long, 2 pieces – 48″ long TOP RIDGE
- PART 1: 14×14 Pavilion Plans
- PART 2: 14x14 Pavilion Roof Plans
It’s that easy to build a pavilion – Video!
How to build a 14×14 pavilion
The first step of the project is to layout the posts for the 14×14 pavilion. Use batter boards and string to determine the location of the posts. Apply the 3-4-5 rule to every corner of the pavilion, so you make sure they are right angled. Moreover measure the diagonals and make sure they are equal. Determining the location for the pavilion is essential, as you have to comply with the local building codes. Make sure the surface is level and remove the vegetation layer.
Dig 3′ deep holes into the ground with a post hole digger. Align the holes with attention and then fit form tubes. Fit the 6×6 posts with attention and align them using string. Use a spirit level to plumb the posts and then lock them into place with temporarily braces. Fill the tube forms with concrete and let it dry out for a few days.
Use 6×6 lumber for the rails. Mark the cut lines on the beams and then make the cut outs with a circular saw and a chisel. Smooth the surface with sandpaper. Use 6×6 lumber for the other rails. Set the circular saw at 2 3/4″ and then make parallel cuts inside the marked areas. Clean the recess with a chisel and sandpaper.
Fit the top rails to the sides, to the front and to the back of the pavilion. Align the edges flush, making sure the corners are square, drill pilot holes and insert 6 1/2″ screws.
Build the braces for the front and back of the pavilion from 6×6 lumber. Use a miter saw to make 45 degree cuts to both ends of the braces. Fit the braces to the posts, after you plumb them vertically. Drill pilot holes and insert 5 1/2″ screws to secure the braces into place tightly.
Fit the 6×6 supports to the top of the plates. Plumb the supports with a spirit level and then attach the top ridge. Make sure the corners are square and then insert 6 1/2″ screws.
Fit the braces to the top ridge. Cut both ends of the braces at 45 degrees and then secure them into place with 5 1/2″ screws.
Check out PART 2 of the project to learn how to build the gable roof.
Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-220 grit sandpaper and remove the residues with a damp cloth.
Top Tip: Apply a few coats of paint or stain to the components, to enhance the look of the project.
This woodworking project was about 14×14 outdoor pavilion plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.