This step by step diy woodworking project is about a 12×12 outdoor pavilion roof plans. This is PART 2 of the square pavilion project, where I show you how to build the roof and how to attach the decorative trims. The roof has a 45 degree slope, so you can easily drain the water or snow. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.
Projects made from these plans
12×12 Pavilion Roof Plans
[tabs tab1=”Materials” tab2=”Tools” tab3=”Time” tab4=”Related Plans”] [tab id=1]
- D – 20 pieces of 2×6 lumber – 120″ long RAFTERS
- E – 4 pieces of 1×6 lumber – 46 3/4″ long TRIMS
- F – 4 pieces of 3/4″ plywood – 48″x96″ long, 4 pieces – 48″x72″ long, 2 pieces – 21 1/4″x96″ long, 2 pieces – 21 1/4″x72″ long ROOF
- G – 300 sq ft of tar paper, 300 sq ft of asphalt shingles ROOFING
- H – 2 pieces of 1×6 lumber – 168″ long TRIMS
- 20 pieces of 2×6 lumber – 10′
- 2 pieces of 1×6 lumber – 8′
- 2 pieces of 1×6 lumber – 14′
- 10 pieces of 3/4″ plywood – 4’x8′
- 300 sq ft of tar paper, 300 sq ft of asphalt shingles
- rafter ties
- 1 5/8″ screws, 2″ nails
- wood glue, stain/paint
[/tab] [tab id=2]
[/tab] [tab id=3]
- PART 1: 12×12 Pavilion Plans
- PART 2: 12x12 Pavilion Roof Plans
How to build a 12×12 pavilion roof
The first step of the project is to build the rafters for the 12×12 pavilion, using 2×6 lumber. Mark the cut lines on the rafters and get the job done with a saw. Smooth the edges with sandpaper, for a professional result.
Fit the rafters to the top of the pavilion, as shown in the plans. Use rafters ties to secure the rafters into place.
Use 1×6 lumber for the gable end trims. Make 45 degree cuts to one end of the trims.
Drill pocket holes at both ends of the gable end trims and then secure them into place with 1 1/4″ screws.
Cut the roofing sheets from 3/4″ plywood and then lay them to the roof of the pavilion. Align the edges flush and leave no gaps between the sheets. Insert 1 5/8″ screws every 8″ along the rafters, so you lock them into place tightly.
Fit 1×6 trims to both sides of the roof. Adjust the width of the trims to 4″ and then secure them into place with 2″ brad nails.
Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. Secure the tar paper to the plywood sheets with roofing staples. In addition, cut a large piece for the top ridge. Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under.
Read the instructions labeled on the asphalt shingle packs before installing them into place tightly. Start with the bottom left side of the roof and install them all the way to the top.
Last but not least, you need to take care of the finishing touches. Fill the holes with wood putty and then smooth the surface with 120-220 grit sandpaper. Apply a few coats of paint or stain over the components, so you protect them from decay and to enhance the look of the pavilion.
This 12×12 pavilion is a good compromise if you are tight on space, but you still want to build a beautiful pavilion, so you can shelter a table, a sofa or a play area. This pavilion is sturdy and it features straight forward techniques, so anyone can get the job done in a professional manner.
This woodworking project was about 12×12 outdoor pavilion roof plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.