10×12 Pavilion Roof Plans

This step by step diy woodworking project is about a 10×12 outdoor pavilion roof plans. This is PART 2 of the rectangular pavilion project, where I show you how to build the roof. This roof has a 2:1 pitch, but you can adjust it super easily. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.

Projects made from these plans

10×12 Pavilion Roof Plans

Building-a-10×12-gable-pavilion

[tabs tab1=”Materials” tab2=”Tools” tab3=”Time” tab4=”Related Plans”] [tab id=1]

• E – 20 pieces of 2×6 lumber – 84″ long RAFTERS
• F – 2 pieces of 3/4″ plywood – 48″x96″ long, 2 pieces – 48″x48″ long, 2 pieces – 36″x96″ long, 2 pieces – 36″x48″ long ROOF SHEETS
• G – 4 pieces of 1×8 lumber – 85 1/4″ long, 2 pieces – 144″ long TRIMS
• H – 200 sq ft of tar paper, 200 sq ft of asphalt shingles ROOFING

• 20 pieces of 2×6 lumber – 8′
• 6 pieces of 3/4″ plywood – 4’x8′
• 2 pieces of 1×8 lumber – 12′
• 4 pieces of 1×8 lumber – 8′
• 200 sq ft of tar paper, 200 sq ft of asphalt shingles
• rafter ties
• 1 5/8″ screws, 2″ nails, 2 1/2″ screws
• wood glue, stain/paint

[/tab] [tab id=2]

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

[/tab] [tab id=3]

 One day

[/tab][tab id=4]

• PART 1: 10×12 Pavilion Plans
• PART 2: 10x12 Pavilion Roof Plans

[/tab][/tabs]

Make sure you follow me on Facebook to be the first that gets my latest plans and for some other exclusive content. Also, follow me on Pinterest to get many ideas for your backyard from all the internet! Check out my YouTube channel! See how you can Support Me with no extra costs to you. 

How to build a 10×12 pavilion roof

Rafters-for-10×12-gable-pavilion

Use 2×6 lumber for the rafters. Make 28.1 degree cuts to both ends of the 2×6 rafters. Mark the cut lines to the rafters and then get the job done with a circular saw. Smooth the edges with sandpaper. Make the notches into the rafters, so you can fit them into place tightly.

Fitting-the-rafters—10×12-pavilion

Fit the rafters to the top of the pavilion, using the information from the diagram. It is important to space the rafters properly (every 16″ on center), otherwise you won’t be able to attach the roofing sheets. Use rafters ties to lock the beams into place.

Roof sheets

Use 3/4″ plywood for the roof of the pavilion. Cut the sheets at the right dimensions and then lay them to the top of the pavilion. Leave no gaps between the sheets and then insert 1 5/8″ screws, every 8″ along the rafters, so you can secure them into place tightly.

Side roof trims

Fit 1×8 trims to the sides of the pavilion. Align the edges with attention and insert 2″ nails to lock them into place tightly.

Gable-end-roof-trims

Fit the 1×8 trims to the front and back of the pavilion. Make the angle cuts to the trims before locking them into place with 2″ nails.

Fitting the roofing

Cover the roof with tar paper and then install the asphalt shingles. Make sure you also install the appropriate drip edges, so you can seal the shed roof. Read the manufacturer’s instructions for a tight fit.

10×12 Picnic Table Plans

Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-200 grit sandpaper and remove the residues with a damp cloth. Apply a few coats of stain or paint to enhance the look of the pavilion.

10×12 Picnic Table Plans – Front view

Don’t forget to take a look over PART 1 of the project, so you learn how to build the frame of the 10×12 pavilion. This pavilion is sturdy and it features a very elegant design that puts and emphasis on cost efficiency and durability. You can add railings to the exterior of the pavilion.

This woodworking project was about 10×12 backyard pavilion roof plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.