Home Indoor Plant Stand With Wine Rack Plans

Plant Stand With Wine Rack Plans

by Ovidiu

 

This step by step diy woodworking project is about plant stand with wine rack plans. This article features detailed instructions for building a plant stand with a wine rack for 4 bottles. This is a basic project that requires basic materials and pocket screws for a professional result. Take a look over the rest of our woodworking plans, if you want to get more building inspiration.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.

 

 

Projects made from these plans

  Add-image

 

 

Plant Stand With Wine Rack Plans

Building a plant stand

Building a plant stand

 

Cut & Shopping Lists

  • A – 4 pieces of 2×2 lumber – 35 1/2″ long LEGS
  • B – 4 pieces of 1×4 lumber – 8″ long TOP SUPPORTS
  • C – 4 pieces of 1×4 lumber – 9″ long FRONT SUPPORTS
  • D – 4 pieces of 1×3 lumber – 9″ long WINE RACK
  • E – 3 pieces of 1×4 lumber – 12″ long LOWER SHELF
  • F – 2 pieces of 1×1 lumber – 13 1/2″ long, 2 pieces – 14 1/2″ long TRIMS
  • G – 1 piece of 3/4″ plywood – 12″x13″ long TOP

Tools

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

Time

 One day

Tools

 

 

Building a wine rack plant stand

Front

Front

The first step of the project is to assemble the front for the plant stand. Use 2×2 lumber for the legs, 1×4 lumber for the supports and 1×3 lumber of the wine rack boards. Drill pocket holes at both ends of the slats and secure them to the legs using 1 1/4″ screws. Add glue to the joints and make sure the corners are square.

Assembling the back

Assembling the back

Assemble the back of the wine rack, as shown in the diagram. Drill pocket holes at both ends of the slats and secure them to the legs with 1 1/4″ screws. Add glue to the joints. Use a jigsaw to make the curved cuts to the wine rack supports.

Building the front supports

Building the front supports

More details for cutting out the holes for front wine supports.

Building the back wine supports

Building the back wine supports

Building the back wine supports explained.

Assembling the wine rack plant stand

Assembling the wine rack plant stand

Assemble the frame of the wine rack from 1×4 lumber. Drill pocket holes at both ends of the slats. Fit them to front and back of the wine rack. Use 1 1/4″ screws and glue to lock the supports into place. Make sure the corners are right-angled for a professional result.

Assembling the top

Assembling the top

Build the top from 3/4″ plywood. Smooth the edges with sandpaper and attach 1×1 trims to top panel. Cut both ends of the trims at 45 degrees, add glue to the joints and secure them to the top with 1 1/2″ brad nails.

Fitting the top

Fitting the top

Center the frame of the plant stand to the tabletop. You can drill pocket holes through the top braces and insert 1 1/4″ screws into the top. Alternatively, you can insert 1 1/2″ brad nails through the top into the frame of the plant stand. Add glue to the joints for a professional result.

Shelf slats

Shelf slats

Use 1×4 lumber for the bottom shelf. Mark the cut lines on the slats that are placed around the legs and get the job done with a circular saw. Smooth the edges with sandpaper.

Fitting the shelf slats

Fitting the shelf slats

Fit the slats to the lower braces and place them equally-spaced. Use 1 1/2″ brad nails to lock the slats into place. Leave no gaps between the components.

Building a wine rack table

Building a wine rack table

Next, you need to take care of the finishing touches. Fit the wood plugs to the pocket holes to get a professional result.

Plant stand with wine rack plans

Plant stand with wine rack plans

Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-220 grit sandpaper and remove the residues with a damp cloth.

Top Tip: Apply a few coats of paint or stain to the components, to enhance the look of the project.

 

 

This woodworking project was about plant stand with wine rack stand plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

 

 

EXPLORE MORE IDEAS FOR:

You may also like

8 comments

Debora Cadene -

Thank you for the plans, I think i’m going to make this as a gift. I was wondering if you have better directions on making the bottle slats though….What am I using to get these grooves, and how.

thank you;.

Debbie.

Reply
Julian -

For the front slats you can use a hole saw drill bit or use something round such as a cap or maybe a large coin (use a jigsaw to make the cuts). For the back slats you can use a round item, but significantly larger, such as plate or similar. When dealing with curved lines, you need to improvise.

Reply
Debora Cadene -

Do you think its possible to be more specific in making these holes? There is nothing saying how far from the ends, or spacing between the grooves. I’d sure appreciate any info you’d be willing to share, as would many others as well.

thank you,
debbie.

Reply
Julian -

I’ve added more diagrams. Hope this helps and makes things more clear.

Reply
Debora Cadene -

Thanks Julian, that was Exactly what I was looking for. You have a GREAT day.

Reply
Julian -

You’re welcome. Looking forward to seeing how the project comes out!

Reply
Kyla -

Am I missing a bottom 12″ piece for the lower shelf? It says to make 2 but the diagrams show 3?

Reply
Ovidiu -

Thank you. I’ve updated the list.

Reply

Leave a Reply to Kyla Cancel Reply