This step by step diy project is about diy 4×4 lean to shed roof plans. This is PART 2 of the lean to shed project, where I show you how to build the lean to roof for the 4×4 shed. Moreover, I have designed shed with many sizes so check them out, as well. Roof pitch is 2:12. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.
Projects made from these plans
4×4 Lean to Shed Roof Plans
Building-a-4×4-lean-to-shed
Cut List
- H – 2 pieces 5/8″ T1-11 siding – 48″x94 1/2″ long SIDING
- G – 4 pieces of 2×4 lumber – 60 3/4″ long RAFTERS
- I – 1 piece of 1/2″ plywood – 4’x60 3/4″ long ROOF
- J – 2 pieces of 1×6 lumber – 60 3/4″ long, 2 pieces – 50 1/2″ long ROOF TRIMS
- K – 30 sq ft of tar paper, 30 sq ft of asphalt shingles ROOFING
- L – 2 pieces of 2×4 lumber – 79″ long, 1 piece – 43″ long JAMBS
- M – 2 pieces of 2×4 lumber – 72″ long, 2 pieces – 36″ long, 1 piece – 29″ long, 1 piece of T1-11 siding – 36″x79″ long 2xDOOR
- P – 2 pieces of 1×4 lumber – 82 1/4″ long, 2 pieces – 89 3/4″ long, 2 pieces – 81 3/4″ long, 2 pieces – 90″ long TRIMS
- UNLOCK PREMIUM PLANS
Tools
Hammer, Tape measure, Framing square, Level, Pocket hole jig
Miter saw, Drill machinery, Screwdriver, Sander
Time
One day
Related
- PART 1: 4×4 Lean to Shed Plans
- PART 2: 4×4 Lean to Shed Roof Plans
Building a 4×4 lean to roof
Building-the-rafters
Build the rafters from 2×4 lumber. Mark the cut lines on the slats and get the job done with a circular saw.
Fitting-the-rafters
Fit the rafters to the top of the lean to shed. Place the rafters every 16″ on center and lock them into place with rafter ties and 1 1/2″ structural screws.
Side panels
Cut the panels for the lean to ends and secure them into place with 6-8d nails. Leave no gaps between the panels for a neat result.
Roof sheet
Lay the 3/4″ plywood sheets to the top of the shed starting with the bottom of the roof. Use 1 5/8″ screws to secure the sheets into place, every 8″ along the rafters.
Roof-trims—4×4-lean-to-shed
Fit the 1×6 trims to the sides of the shed. Align the edges flush, leave no gaps between the boards and then lock them into place with 2″ nails.
Fitting the roofing
Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. Secure the tar paper to the plywood sheets with roofing staples. Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under.
Building the shed door
Door jambs
Use 2×4 lumber for the door jambs. Fit the door jambs around the door and then secure them into place with 3 1/2″ screws.
Building-shed-door-frame
Use 2×4 lumber for the door frame. Drill pocket holes at both ends of the vertical and middle components. Align the edges flush and insert 2 1/2″ screws to assemble the door frame.
Door panel
Use T1-11 siding sheets for the door panel. Align the edges flush and insert 1 5/8″ screws to secure the panel to the frame. Add glue to the joints.
Fitting the door
Fit the doors to the opening and then align the edges flush. Use hinges to secure the doors to the jambs. Also, set a latch so you can keep the doors locked.
Fitting the side trims
Use 1×3 lumber for the exterior trims. Make angle cuts to the top of the trims and then secure them into place with 2″ nails.
trims
Back trims
Fit the trims to the front and back of the shed.
4×4 shed – overall height
Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-220 grit sandpaper and remove the residues with a damp cloth.
Top Tip: Apply a few coats of paint or stain to the components, to enhance the look of the project. Check PART 1 of the project to learn how to build the frame of the shed.
This woodworking project was about 4×4 lean to shed roof plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.
- EXPLORE MORE IDEAS FOR -
 |
 |
 |
 |
