10×12 Gable Pavilion Roof

This step by step diy woodworking project is about a 10×12 pavilion roof plans. This is PART 2 of the rectangular pavilion project, where I show you how to build the roof. This roof has a 8:12 pitch, but you can adjust it super easily. You can play with the roof pitch to suit your needs. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.

Projects made from these plans

10×12 Gable Pavilion Roof Plans

Building a 10×12 gable pavilion

Cut & Shopping Lists

F – 24 pieces of 2×6 lumber – 90″ long RAFTERS
G – 2 pieces of 3/4″ plywood – 48″x80″ long, 2 pieces – 48″x96″ long, 2 pieces – 42″x80″ long, 2 pieces – 42″x96″ long ROOF SHEETS
H – 4 pieces of 1×8 lumber – 91 1/4″ long, 2 pieces – 176″ long TRIMS
I – 260 sq ft of tar paper, 260 sq ft of asphalt shingles ROOFING

UNLOCK SHOPPING LISTS

Tools

Hammer, Tape measure, Framing square, Level

Miter saw, Drill machinery, Screwdriver, Sander

Safety Gloves, Safety Glasses

Time

One day

PART 1: 10×12 Pavilion Plans
PART 2: 10x12 Pavilion Roof Plans

How to build a 10×12 gable pavilion roof

Rafters-for-pavilion

End-of-rafters

Use 2×6 lumber for the rafters. Make 33.5 degree cuts to one end of the 2×6 rafters. Mark the cut lines to the rafters and then get the job done with a circular saw. Smooth the edges with sandpaper. Make the notches into the rafters, so you can fit them into place tightly.

Fitting-the-rafters—small-gable-pavilion

Fit the rafters to the top of the pavilion, using the information from the diagram. It is important to space the rafters properly (every 16″ on center), otherwise you won’t be able to attach the roofing sheets. Use rafters ties to lock the beams into place.

Roof-sheets—pavilion

Use 3/4″ plywood for the roof of the pavilion. Cut the sheets at the right dimensions and then lay them to the top of the pavilion. Leave no gaps between the sheets and then insert 1 5/8″ screws, every 8″ along the rafters, so you can secure them into place tightly.

Fitting-the-side-roof-trims

Fit 1×8 trims to the sides of the pavilion. Align the edges with attention and insert 2″ nails to lock them into place tightly.

Front-end-trims

Fit the 1×8 trims to the front and back of the pavilion. Make the angle cuts to the trims before locking them into place with 2″ nails.

Front-end-trims

Cover the roof with tar paper and then install the asphalt shingles. Make sure you also install the appropriate drip edges, so you can seal the shed roof. Read the manufacturer’s instructions for a tight fit.

10×12-Pavilion—front-view

Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-200 grit sandpaper and remove the residues with a damp cloth. Apply a few coats of stain or paint to enhance the look of the pavilion.

How-to-build-a-10×12-gable-pavilion

Don’t forget to take a look over PART 1 of the project, so you learn how to build the frame of the 10×12 pavilion. This pavilion is sturdy and it features a very elegant design that puts and emphasis on cost efficiency and durability. See all my woodworking plans, sorted by category.

This woodworking project was about 10×12 backyard pavilion roof plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.