5×6 Deer Blind Roof Plans

This step by step diy woodworking project is about 5×6 deer stand roof plans. This is PART 2 of the deer stand project, where I show you how to build the gable roof. This gable roof for the deer blind is sturdy and super easy to build. Make sure you take a look over the rest of plans to see alternatives and more projects for your garden.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.

Projects made from these plans

5×6 Deer Blind Roof Plans

Building-a-5×6-deer-blind

Cut & Shopping Lists

• F – 2 pieces of 1/2″ plywood – 48″x92 3/4″ long, 2 pieces – 24″x88 3/4″ long, 2 pieces – 48″x80 1/2″ long, 2 pieces – 12″x80 1/2″ long PANELS
• H – 10 pieces of 2×4 lumber – 39 1/8″ long RAFTERS
• H – 4 pieces of 2×4 lumber – 39 5/8″ long, 2 pieces – 64″ long TRIMS
• H – 2 pieces of 3/4″ plywood – 40″x64″ long ROOF
• I – 50 sq ft of tar paper, 50 sq ft of asphalt shingles ROOFING
• J – 1 piece of 3/4″ plywood – 26 1/4″x70″ long, 2 pieces of 2×2 lumber – 26 1/4″ long, 2 pieces – 67″ long, 1 piece – 23 1/4″ long DOOR

• 9 pieces of 2×4 lumber – 8′
• 3 pieces of 2×2 lumber – 8′
• 6 pieces of 1/2″ plywood – 4’x8′
• 2 pieces of 3/4″ plywood – 4’x8′
• 1 5/8″ screws
• 2 1/2″ screws
• 4 1/2″ screws
• 50 sq ft of tar paper
• 50 sq ft of asphalt shingles
• 1 latch

Tools

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

Time

 One week

Make sure you follow us on Facebook to be the first that gets our latest plans and for some other exclusive content. Also, follow us on Pinterest to get many ideas for your backyard from all the internet! Check out our YouTube channel! See how you can Support Us with no extra costs to you. 

How to build the roof a deer stand

Rafter-plans—5×6-gable-deer-blind

The first step of the project is to build the rafters for the deer stand from 2×4 lumber. Use a saw to make the cuts to the rafters, as shown in the plans. Smooth the edges with sandpaper.

Fitting-the-rafters

Fit the rafters to the top of the deer stand. Place the rafters every 16″ on center and then lock them into place with screws.

Fitting the side panels

The next step of the shooting house is to attach the 1/2″ plywood panels to the side walls. As you can notice in the diagram, you need to make a few cut outs for the windows. Smooth the edges with sandpaper. Attach the panels to the frames and align the edges with attention. Insert 1 5/8″ screws to secure the panels to the framing, every 8″ along the studs and plates.

Front wall panels

Cut the 1/2″ plywood panels that go on the front wall of the deer stand. Make the cuts as shown in the plans and then secure them into place with 1 5/8″ screws, every 8″ along the framing.

Back wall panels

Cut the panels for the back wall and then secure them into place.

Front and back roof trims

Cut and fit the 2×4 trims to the front and back of the deer stand. Use 3 1/2″ screws to lock the trims into place tightly.

Side roof trims

Fit the 2×4 trims to the sides of the deer stand. Align the edges and use a spirit level to make sure the trims are horizontal. Drill pilot holes and insert 3 1/2″ screws.

Fitting the roof sheets

Build the roof of the deer stand from 3/4″ plywood. Cut the sheets at the right dimensions and center them to the rafters. Use 1 5/8″ screws to secure the sheets into place, every 8″.

Fitting the roofing

Cover the roof with tar paper. Use staples to secure the tar paper into place. Next, you should install asphalt shingles to the roof, starting from the bottom up to the top. Install a ridge cap to waterproof everything in a professional manner.

Building-the-door—deer-house

Build the door from 2×2 lumber and 1/2″ plywood. Cut the plywood panel at 26 1/4″x49 1/2″ or you can use the piece that has been cut out when building the back wall. Attach 2×2 trims to the panel, as shown in the diagram. Use 2 1/2″ screws to assemble the frame. Use 1 5/8″ to lock the frame to the panel.

Fitting the door

Fit the door to the opening and lock it to the wall with hinges. Install a latch to keep it tightly closed.

5×6 Deer Blind Plans

Now that you have assembled everything with attention, we recommend you to cover the exterior components with a few coats of paint.

5×6 Deer Stand Plans

This deer blind has a basic design and can be built by any person with common woodworking skills. You can adjust the dimensions of the deer box, while using the same techniques described in the plans.

Top Tip: Make sure you check out PART 1 of this project, to learn more about how to build the frame of the elevated deer box.

This woodworking project was about 5×6 deer stand gable roof plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

- EXPLORE MORE IDEAS FOR -