This step by step diy woodworking project is about a 24×48 gable pavilion plans. This is a large pavilion built on a sturdy 6×6 and 6×8 framing, so you can enjoy your garden and create a large shaded area, perfect for picnic or other outdoor activities. The roof for this pavilion has a pitch of 6:12 and features large opening on all sides. Make sure you take a look over the local building codes, so you comply with the regulations. Take a look over the rest of our woodworking plans, if you want to get more building inspiration. Premium Plans for this project available Here. Check out the Shop, as well, for full list of Premium Plans.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.
Projects made from these plans
24×48 Gable Pavilion Plans – PDF Download
24×48 pavilion plans – building
Cut and Materials Lists
Tools
Hammer, Tape measure, Framing square, Level
Miter saw, Drill machinery, Screwdriver, Sander
Safety Gloves, Safety Glasses, Post hole digger
Time
One week
Related
- PART 1: 24×48 Pavilion Plans
- PART 2: 24×48 Gable Pavilion Roof Plans
It’s that easy to make a 24×48 pavilion!
How to build a 24×48 pavilion
Laying-out-the-posts-DIY
First, layout the posts for the large pavilion. Use batter boards and string to determine the location of the posts. Apply the 3-4-5 rule to every corner of the pavilion, so you make sure they are right angled.
Make sure the diagonals are equal. Determining the location for the pavilion is essential, as you have to comply with the local building codes. Make sure the surface is level and remove the vegetation layer.
Setting the posts in concrete
Dig 3 ft holes into the ground, making sure they have about 14″ in diameter. Fit the tubes then fill them with concrete and set the anchors. Align the anchors one to another and let the concrete dry out for several days. Next, attach the 6×6 posts to the anchors and plumb them with a spirit level. Use temporarily braces to lock the posts into place till you assemble the whole frame of the pavilion.
Read the local codes for more details on how to secure the posts. Use lag screws to secure the posts to the anchors. Before pouring the concrete you need to make sure the top of the posts are horizontal one to another. Use a laser to mark the level to the top of the posts and use a circular saw, if you need to make cuts.
Building the frame of the pavilion
Top-plates
Next, we will be building the top plates for the large lean to pavilion. Therefore, this pavilion requires at least 6x10s, due to the large spans on the front and back. As you can see in the diagram, you need to make 3 5/8″ notches to the beams, so you can lock them together tightly.
Use a circular saw to make parallel cuts inside the marked areas and remove the excess with a chisel. Smooth the recesses with sandpaper.
Fitting-the-side-top-plates
Fit the top rails to the sides of the pavilion. Notice the 24″ overhangs to the back of the pavilion. Drill pilot holes through the plates and insert 8″ screws to lock them to the posts. Use 2 screws for each joint. Make sure the corners are square and plumb the posts vertically.
Fitting-the-crossbeams
Next, fit the cross plates to the pavilion. Align the edges flush and drill pilot holes. Insert the 8″ screws to lock the cross plates to the side posts. Use post to beam connectors and 2 1/2″ structural screws to secure the beams to the middle posts.
Fitting the braces
Fitting-the-braces—frame
Build the braces for the front and back of the pavilion from 6×6 lumber. Use a miter saw to make 45 degree cuts to both ends of the braces. Fit the braces to the posts, after you plumb them vertically. Drill pilot holes and insert 5 1/2″ screws to secure the braces into place tightly. Insert at least 2 screws for each joint. Adding these braces will make the structure 10 times more rigid.
Fitting-the-support-beams
Center the 6×6 supports to the top of pavilion. Plumb the supports with a spirit level. Use post to beam connectors to secure the supports to the frame of the pavilion. Insert 2 1/2″ structural screws to lock the supports.
Ridge-beams
Use 6×8 lumber for the ridge beams. Make the notches to the beams, as shown in the diagram.
Fitting-the-ridge-beams
Fit the 6×8 beams to the top of the supports. Notice the 24″ overhangs to the front and back of the pavilion. Use post to beam connectors with 2 1/2″ structural screws to lock everything together tightly. Insert structural screws through the connector. Make sure the corners are square and align the edges flush.
Finishing touches
24×48 pavilion plans – dimensions
Check out PART 2 of the project to learn how to build the gable roof. You can see in this image the overall dimensions for the large pavilion. This is really useful because it can shelter a picnic table or even an outdoor entertainment area. Moreover, this makes for a nice triple carport.
24×48 pavilion plans
24×48 pavilion plans – front view
Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-220 grit sandpaper and remove the residues with a damp cloth.
Top Tip: Apply a few coats of paint or stain to the components, to enhance the look of the project. Check out the Shop, as well, for full list of Premium Plans.
This woodworking project was about 16×48 lean to pavilion plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.
- EXPLORE MORE IDEAS FOR -
 |
 |
 |
 |
