This step by step diy woodworking project is about 12×24 run in shelter roof plans. This article is PART 2 of the loafing shelter project. Therefore, if you want to build the lean to roof for the 12×24 shelter, take a look over this article. Make sure you check out the rest of plans to see alternatives and more projects for your garden.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.
Projects made from these plans
12×24 Loafing Shed Roof Plans
- F – 13 pieces of 2×6 lumber – 14′ long RAFTERS
- G – 2 pieces of T1-11 – 17 3/4″x48″ long, 2 pieces – 30 1/4″x48 long, 2 pieces – 42 1/2″x48″ long SIDING
- H – 7 pieces of 3/4″ plywood – 48″x96″ long, 2 pieces – 24″x48″ long, 2 pieces – 48″x72″ long, 3 pieces – 24″x96″ long ROOF SHEETS
- I – 2 pieces of 1×6 lumber – 168″ long, 2 pieces – 290 1/4″ long TRIMS
- J – 350 sq ft of tar paper, 350 sq ft of asphalt shingles ROOFING
- K – 4 pieces of 1×6 lumber – 140 1/2″ long, 2 pieces – 207 1/2″ long INTERIOR CLEATS
- 8 pieces of 2×4 lumber – 8′
- 13 pieces of 2×6 lumber – 14′
- 11 pieces of 3/4″ plywood – 4’x8′
- 2 pieces of T1-11 siding – 4×8′
- 12 pieces of 1×6 lumber – 14′
- 350 sq ft of tar paper
- 350 sq ft of asphalt shingles
- 500 pieces of 2 1/2″ screws
- 200 pieces of 1 5/8″ screws/brad nails
How to build a 12×24 run in shed roof
First of all, you need to build the rafters for the shed roof. Use 2×6 beams, as the rafters need to support a lot of weight, especially if you live in a snowy area.
Make a small notch to the bottom of the rafters, as shown in the diagram. Smooth the recess with sandpaper.
Fit the rafters to the top of the run in shed. Place the rafters equally-spaced, using the instructions from the diagram. Toe nail the rafters to the structure or use appropriate metal connectors.
Continue the project by attaching the siding sheets to the sides of the run in shed. Align the sheets with attention and lock them into place with 1 5/8″ screws/nails. Leave no gaps between the sheets for a professional result. As you can notice, the side siding will also cover the rafters and roofing sheets.
Attach 3/4″ plywood sheets to the rafters, using the pattern shown in the diagram. Drill pilot holes and insert 1 5/8″ screws, every 8″ along the rafters. Leave no gaps between the tongue and groove sheets.
In order to enhance the look of the large run in shed, you need to attach 1×6 trims to the sides and to the front and back faces. Use brad nails to secure the trims into place, after aligning the edges with attention.
Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. Secure the tar paper to the plywood sheets with roofing staples. In addition, cut a 12″ piece for the top ridge. Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under.
Fit 1×4 cleats to the interior of the shed, as shown in the diagram. Attach the cleats into place with 2 1/2″ screws. You can adjust the size of the interior walls to suit your needs.
Next, attach the 1×6 vertical slats to the cleats. Use 1 5/8″ screws to lock the slats to the cleats.
The loafing shed is roomy enough for your cattle. Make sure everything is locked together tightly.
Apply a few coats of paint over the components, to protect them from decay and to enhance the look of the shed.
Top Tip: Check out the rest of the project, to learn how to build the frame for the 12×24 run in shed.
This woodworking project was about 12×24 shed roof plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.