Home Shed 12×14 Run in Shed Roof Plans

12×14 Run in Shed Roof Plans

by Ovidiu


This step by step diy woodworking project is about 12×14 run in shed roof plans. This article is PART 2 of the run in shed project, where I show you how to frame the lean to roof and how to fit the decorative trims. Make sure you check out the rest of plans to see alternatives and more projects for your garden.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.



Projects made from these plans




12×14 Run in Shed Roof Plans




Cut & Shopping Lists

  • E – 6 pieces of T1-11 siding – 48″x90″ long, 2 pieces – 43 3/4″x48″ long, 2 pieces – 31 3/4″x48″ long, 2 pieces – 19 1/2″x48″ long SIDING
  • G – 12 pieces of 2×8 lumber – 168″ long, 2 pieces of 2×4 lumber – 23 1/4″ long, 2 pieces – 10 1/4″ long RAFTERS
  • H – 3 pieces of 3/4″ plywood – 48″x96″ long, 2 pieces – 48″x72″ long, 1 piece – 24″x48″ long, 1 piece – 24″x48″ long, 1 piece – 24″x96″ long, 1 piece – 24″x48″ long, 1 piece – 24″x24″ long ROOF SHEETS
  • H – 200 sq ft of tar paper, 200 sq ft of asphalt shingles ROOFING
  • I – 2 pieces of 2×10 lumber – 168″ long, 2 pieces of 1×10 – 172 1/4″ long TRIMS


 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses


 One week



Building a 12×14 shed roof plans



Build the rafters from 2×8 lumber. Make notches to the rafters, using the information from the diagram. Smooth the recesses with sandpaper.



Fit the rafters to the top of the run in shed. Drill pilot holes and lock the rafters to the structure with screws and rafter ties. Place the rafters every 16″ on center.

Side roof supports

Side roof supports

Use 2×4 lumber for the side lean to roof supports. Make the angle cuts with a miter saw and then lock them into place tightly with screws.

Side siding panels

Side siding panels

Attach T1-11 siding to the back wall of the shelter. Use 6d brad nails to lock the sheets into place tightly. Insert the nails every 8″ along the wall framing.



Cut the 3/4″ plywood sheets at the right dimensions, as shown in the diagram. Align the edged with attention and leave no gaps between the sheets. Insert 1 5/8″ screws, every 8″ along the framing.

Side roof trims

Side roof trims

Fit the 2×10 trims to the sides, to the front and to the back of the shed. Cut the components at the right dimensions and then align them into place with attention. Drill pilot holes and then insert 3 1/2″ nails, every 8″ along the framing.

Front and back roof trims

Front and back roof trims

Attach 1×10 trims to the front and back of the roof. Use 3 1/2″ screws to secure the trims into place tightly.

Fitting the roofing

Fitting the roofing

Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. Secure the tar paper to the plywood sheets with roofing staples. In addition, cut a 12″ piece for the top ridge. Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under.

12x14 Run In Shed Plans

12×14 Run In Shed Plans

Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-200 grit sandpaper and remove the residues with a damp cloth.

Top Tip: Check out PART 1 of the project, to learn how to build the frame for the 12×12 run in shed.



This woodworking project was about 12×14 run in shelter plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.







You may also like

Leave a Comment