4×6 Lean to Shed Roof Plans

This step by step diy project is about 4×6 lean to shed roof plans. This is PART 2 of the free 4×6 attached shed plans, where I show you how to build the lean to roof and how to attach the siding sheets. Make sure you check the local codes and make adjustments to the plans, if required. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. See all my Premium Plans HERE.

Projects made from these plans

4×6 Lean to Shed Roof Plans

Building-a-4×6-shed

Cut & Shopping Lists

• E – 3 pieces of  T1-11 siding – 48″x90″ long, 1 piece – 24″x90″ long, 2 pieces – 26 1/2″x48″ long SIDING
• F – 6 pieces of 2×4 lumber – 61 1/2″ long RAFTERS
• G – 1 piece of 3/4″ plywood – 48″x72″ long, 1 piece – 13 1/2″x72″ long ROOF
• H – 40 sq ft of tar paper, 40 sq ft of asphalt shingles ROOFING
• I – 2 pieces of 2×6 lumber – 61 3/4″ long, 1 piece of 1×6 lumber – 76 1/4″ long TRIMS

• 4 pieces of 5/8″ T1-11 – 4’x8′
• 6 pieces of 2×4 lumber – 6′
• 2 pieces of 3/4″ plywood – 4’x8′
• 1 piece of 1×6 lumber – 8′
• 2 pieces of 2×6 lumber – 6′
• 40 sq ft of tar paper, 40 sq ft of asphalt shingles
• tar paper
• 6d nails, 2 1/2″ screws, 3 1/2″ screws
• wood filler , wood glue, stain/paint

Tools

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

Time

 One week

Related

• PART 1: 4×6 Shed Plans
• PART 2: 4×6 Lean to Shed Roof Plans
• PART 3: 4×6 Double Door Plans

Building a 4×6 lean to shed roof

Front wall panels

Fit the T1-11 siding to the front of the wall. As you can see in the diagram, you need to mark the cut lines on the sheets and get the job done with a circular saw. Align the edges flush and insert 6-8d nails, every 8″ along the framing.

Building-the-rafters–

Use 2×4 lumber for the rafters. Mark the cut lines on the boards and then get the job done with a circular saw.

Fitting the rafters

Fit the rafters to the top of the shed, every 16″ on center. Use rafter ties to lock the rafters into place tightly.

Side wall panels

Fit the T1-11 siding sheets to the sides of the shed. Align the edges and insert 6-8d nails, every 8″ along the framing.

Roof-sheets—attached-4×6-shed

Fit the 3/4″ plywood sheets to the roof of the shed. Align the edges with attention and insert 1 5/8″ screws, every 8″ along the framing.

Roof trims

Fit 2×6 trims to the sides of the roof. Fit 1×6 trims to the front of the shed. Align the edges with attention, drill pilot holes and insert 3 1/2″ screws.

Fitting the roofing

Cover the roof with tar paper and then install the asphalt shingles. Make sure you also install the appropriate drip edges, so you can seal the shed roof. Read the manufacturer’s instructions for a tight fit.

4×6 Attached Lean to Shed

I have lots of other shed projects on the site so I recommend you to browse through all alternatives before starting the building project. See all my shed projects HERE. Moreover, check out PART 1 of the shed, so you learn how to build the frame of the shed. Check out PART 3 of the shed, so you learn how to build the double doors.

This woodworking project was about 4×6 lean to shed roof plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

- EXPLORE MORE IDEAS FOR -