This step by step diy woodworking project is about a 16×10 wooden gable pavilion plans. This pavilion features a gable roof that is built on a 4 post structure. The gazebo has a wide opening to the front and it is perfect is you want to cover something wide. The roof pitch is 6:12. Make sure you take a look over the local building codes, so you comply with the regulations. Take a look over the rest of our woodworking plans, if you want to get more building inspiration. Check out the Shop, as well, for full list of Premium Plans.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.
Pin for Later!
Projects made from these plans
16×10 Gable Pavilion Plans – DIY Plans
Building-a-14×10-gable-pavilion
Cut + Shopping Lists
A – Posts – 6×6 lumber 88 1/4″ long – 4 pieces
B – Top frame – 6×8 lumber 12′ long – 2 pieces
C – Crossbeams – 6×8 lumber 16′ long – 2 pieces
D – Supports – 6×6 lumber 37 3/8″ long – 2 pieces
D – Ridge beam – 6×6 lumber 12′ long – 1 piece
E – Braces – 6×6 lumber 36″ long – 10 pieces
F – Rafters – 2×6 lumber 120″ long – 18 pieces
G – Roof sheets – 3/4″ plywood – 4’x8′ – 4 pieces
G – Roof sheets – 3/4″ plywood – 4’x4′ – 4 pieces
G – Roof sheets – 3/4″ plywood – 2’x8′ – 2 pieces
G – Roof sheets – 3/4″ plywood – 2’x4′ – 2 pieces
H – Trims – 1×8 lumber 121 1/8″ long – 4 pieces
H – Trims – 1×8 lumber 12′ long – 2 pieces
I – Roofing – Underlayment & Asphalt Shingles – 300 sq ft
Tools
Hammer, Tape measure, Framing square, Level
Miter saw, Drill machinery, Screwdriver, Sander
Time
One week
Related
- PART 1: 16×10 Pavilion Plans
- PART 2: 16×10 Pavilion Roof Plans
It’s that easy to build a gable pavilion!
How to build a 16×10 pavilion – laying out
Layout—16×10
First, layout the posts for the 16×10 gable pavilion. Use batter boards and string to determine the location of the posts. Apply the 3-4-5 rule to every corner of the pavilion, so you make sure they are right angled. Make sure the diagonals are equal and make adjustments if necessarily.
Determining the location for the pavilion is essential, as you have to comply with the local building codes. Make sure the surface is level and remove the vegetation layer.
Setting the posts in concrete
Dig 3 ft holes into the ground, making sure they have about 12″ in diameter. Fit the tubes then the posts into the ground and plumb them with a spirit level. Use temporarily braces to make sure the posts are locked into placed while filling the holes with concrete. Let the concrete dry out for several days. Read the local codes for more details on how to secure the posts.
Use lag screws to secure the posts to the anchors. Before pouring the concrete you need to make sure the top of the posts are horizontal one to another. Use a laser to mark the level to the top of the posts and use a circular saw, if you need to make cuts.
Building the frame of the large pavilion
Top-plates—dimensions
Use 6×8 lumber for the rails. Mark the cut lines on the beams and then make the cut outs with a circular saw and a chisel. Smooth the surface with sandpaper. Use 6×8 lumber for the other rails. Set the circular saw at 3 5/8″ and then make parallel cuts inside the marked areas. Clean the recess with a chisel, a hammer and sandpaper.
Installing-the-crossbeams
Fit the crossbeams to the top of the posts, at the front and at the back. Drill pilot holes through the plates and insert 8″ screws to lock them to the posts. Use 2 screws for each joint. Make sure the corners are square and plumb the posts vertically. Use a spirit level to check if the beams are horizontal.
Installing-the-side-top-beams
Fit the top plates to the sides of the pavilion. Align the edges flush and drill pilot holes. Insert the 8″ screws to lock the cross plates into place tightly.
Braces—16×10-pavilion
Build the braces for the front and back of the pavilion from 6×6 lumber. Use a miter saw to make 45 degree cuts to both ends of the braces. Fit the braces to the posts, after you plumb them vertically.
Drill pilot holes and insert 5 1/2″ screws to secure the braces into place tightly. Insert 2 screws for each joint. We need these braces to add rigidity to the pavilion and make it stiff against strong winds.
Building the roof of the pavilion
Fitting-the-ridge-beam-supports
Center the 6×6 supports to the top of pavilion, at the front and back. Plumb the supports with a spirit level. Use post to beam connectors and 2 1/2″ structural screws to secure the supports to the frame of the pavilion.
Remember that the height for these posts is designed for a corresponding 6:12 pitch. If you want a different pitch for your project you need to start by changing the height of these supports.
Attaching-the-ridge-beam
Fit the 6×6 ridge beam to the supports with post to beam connectors. Make sure the corners are square. Notice the 12″ overhangs to the front and back, similar to the side plates. Use 2 1/2″ structural screws to lock the connectors into place.
Ridge-beam-braces
Use 6×6 lumber for the braces. Make 45 degree cuts at both ends of the braces. Secure the braces into place with 5 1/2″ screws. Drill pilot holes before inserting the screws. As usual, use 2 screws for each joint.
Finishing touches
16×10-gable-pavilion—dimensions
Check out PART 2 of the project to learn how to build the gable roof. See the overall dimensions of this pavilion in the image above.
16×10-gable-pavilion-plans
Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-220 grit sandpaper and remove the residues with a damp cloth.
Top Tip: Apply a few coats of paint or stain to the components, to enhance the look of the project. Premium Plans for this project available Here. Check out the Shop, as well, for full list of Premium Plans. Press the GET PDF PLANS button bellow, if you want to get the Premium Plans with the full Cut and Shopping lists included, as well as with the cut layout diagram.
This woodworking project was about 16×10 gable pavilion plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.
- EXPLORE MORE IDEAS FOR -
 |
 |
 |
 |
