14x14 Gable Shed Roof Plans

This step by step diy project is about 14×14 gable shed roof plans. This is PART 2 of the storage shed project, where I show you everything you want to know about framing the gable roof. The roof pitch is 6:12. Take a look over the rest of my woodworking plans, if you want to get more building inspiration. Remember that you need to select the site for the shed with attention and that you have to comply with a few legal regulations.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.

Projects made from these plans

14×14 Gable Shed Roof Plans

Building-a-14×14-gable-shed

Cut + Shopping Lists

UNLOCK LISTS

Tools

Hammer, Tape measure, Framing square, Level

Miter saw, Drill machinery, Screwdriver, Sander

Safety Gloves, Safety Glasses

Time

One week

PART 1: 14×14 Shed Plans
PART 2: 14×14 Shed Roof Plans
PART 3: Shed Doors Plans

Building a 14×14 shed roof

Rafters

The first step of the woodworking project is to build the 2×4 rafters for the shed. As you can easily notice in the diagram, you need to make 26.5 degree cuts to both ends of the slats and then cut the birdsmouth. Smooth the edges with sandpaper for a neat result.

Assembling-the-trusses

Build the bottom chords in the same manner, just notice the new angle of the cut.

Middle-truss-supports

Lay all the rafters on a level surface and then leave no gaps between the components. Cut the vertical support from 2×4 lumber, as well. Make 26.5 cuts to the top of the support.

Trusses

Use 1/2″ plywood for the gussets and then lay them over the joints. Align the edges with attention, drill pilot holes through the gussets and insert 1 5/8″ screws into the rafters. Ideally, you need to fit the gussets on both sides of the trusses.

Fitting-the-trusses

Fit the trusses to the top of the shed, making sure you place them every 16″ on center. Use a spirit level to plumb the trusses and then lock them to the top plates with rafter ties. Insert 1 1/2″ structural screws to lock the connectors into place.

Gable-end-supports

Use 2×4 lumber for the supports that go on both sides of the gable roof. Drill pocket holes at both ends of the supports and secure them into place with 2 1/2″ screws.

Gable-end-panels

Fit the T1-11 siding sheets to the sides of the shed. Make the cuts and secure the panels to the framing, using 6-8d nails, every 8″ along the structure. Use a saw to make the cuts around the double door opening. Attach the panels to the opposite side of the gable shed.

Overhangs

Assembling the overhangs for the shed is a straight forward project, as you need just 2×4 lumber. Drill pilot holes through the rafters and insert 3 1/2″ screws into the blockings. Place the blockings every 16″ on center.

Fitting-the-overhangs

Fit the overhangs to the sides of the shed. Align the edges with attention and drill pilot holes. Insert 3 1/2″ screws so you can secure the overhangs into place tightly.

Shed-roof-sheets

Cut the 1/2″ plywood sheets for the roof of the 10×16 shed. Align the edges with attention, drill pilot holes and insert 1 5/8″ screws, so you can lock them into place tightly. Insert the screws, every 8″ along the rafters for a professional result. Leave no gaps between the sheets for a neat result.

Fitting-the-side-trims

Fit the 1×8 trims to the sides of the shed. Align the edges with attention and then lock them into place with 2″ brad nails.

Gable-end-trims

Cut and fit the decorative trim fascia to the gable ends of the shed. Align the edges flush and insert 2″ nails to lock them into place tightly.

Fitting-the-roof-sheets

Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. Secure the tar paper to the plywood sheets with roofing staples. In addition, cut a large piece for the top ridge.

Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under. Read the instructions labeled on the asphalt shingle packs before installing them into place tightly. Start with the bottom left side of the roof and install them all the way to the top.

14×14 Shed Plans – front view

14×14 Shed Plans – back view

You need to check out PART 3 of the shed, so you learn how to build the double doors and how to fit the rest of the trims. If you haven’t looked over PART 1 yet, I recommend you to do it, as it will show everything you want to know about building the frame of the shed. To get the full PREMIUM PLANS for this design, check out PART 1 or go to my shop (link in menu).

This woodworking project was about 14×14 garden shed plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.