Home 12x14 12×14 Pergola Plans – Free PDF Download

12×14 Pergola Plans – Free PDF Download

by Ovidiu
5.7K views 7 minutes read

 

This step by step diy project is about 12×14 pergola plans. This is a step by step guide for you to build a free standing pergola. This structure will create some shade in your backyard, so you can serve dinner or hang out with the friends. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.

All my woodworking plans come with 3D diagrams and step by step instructions. In addition, the plans include full Cut and Shopping lists. Remember that you need to read the local codes before starting the project. It is your responsibility to make adjustments and suit the legal requirements.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about one weekend. See all my Premium Plans HERE.

 

 

Projects made from these plans

Add-image

 

 

12×14 Pergola Plans – Free PDF Download

Building-a-12x14-pergola

Building-a-12×14-pergola

 

Cut + Shopping Lists

  • A – 4 pieces of 6×6 lumber – 8′ long POSTS
  • B – 4 piece of 2×8 lumber – 14′ long BASE BEAMS
  • C – 4 pieces of 2×8 lumber – 16′ long SUPPORT BEAMS
  • D – 12 pieces of 2×6 lumber – 14′ long SHADE ELEMENTS
  • E – 4 pieces of 6×6 lumber – 36″ long, 4 pieces – 46 1/4″ long BRACES
  • F – 5 pieces of 1×2 lumber – 16′ long SLATS

  • 8 pieces of 6×6 lumber – 8′
  • 4 piece of 2×8 lumber – 14′
  • 4 pieces of 2×8 lumber – 16′
  • 12 pieces of 2×6 lumber – 14′
  • 5 pieces of 1×2 lumber – 16′
  • 1 5/8″ screws
  • 5 1/2″ screws
  • 6×6 post anchor  4 pieces
  • post to beam connector 8 pieces
  • 16 pieces of 9″ carriage bolt
  • wood filler , wood glue, stain/paint

Tools

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

Time

 One week

Related

 

 

Trim---Facebook-BoxMake sure you follow me on Facebook to be the first that gets my latest plans and for some other exclusive content. Also, follow me on Pinterest and Instagram to get many ideas for your backyard from all the internet! Check out my YouTube channel! See how you can SUPPORT  Me with no extra costs to you. Trim---Facebook-Box-Down

 

 

How to build a 12×14 free standing pergola

Laying-out-the-posts-for-the-12x14-pergola

Laying-out-the-posts-for-the-12×14-pergola

The first step of the pergola project is to layout the posts. Use batter boards and string to layout the location of the posts. Apply the 3-4-5 rule to every corner and then measure the diagonals to make sure they are perfectly equal. You need to make adjustments until you get the desired result. As you can see in the image, this pergola has a 12×14 base.

Anchoring the posts of the anchor

Anchoring the posts of the anchor

There are a few ways to secure the 6×6 posts into place. You can set the posts in concrete or you can use adjustable anchors and pour footings. Dig the holes 3′ deep (or under the front line) and about 12-13″ in diameter. Compact a layer of gravel to the bottom of the holes and then fit the tube forms. Fit the posts, align them and plumb them with a spirit level. Fill the forms with concrete, while the posts are locked into place with temporarily braces. If you use anchors, you need to align and set them into concrete. Fit the posts after the concrete dries, using lag screw.

Smart tip: Read the local building codes, so you dig the holes at the appropriate depth. For this project, I will assume you will use post anchors, so if you set the posts into concrete, make sure you add 3′ to the posts size.

Installing the posts

Installing the posts

Check if the posts are level and user a circular saw to make corrections. Notice the temporarily braces that hold the posts plumb.

 

Building the pergola roof

Base beams - 12x14 Pergola

Base beams – 12×14 Pergola

Continue the diy pergola project by making the base beams. Use 2×8 lumber for these beams.

Rafters - end decorative cuts

Rafters – end decorative cuts

You can add a lot of value to your pergola by making decorative cuts to both ends of the beams. Use a circular saw for the straight cuts and a jigsaw for the curved cuts. Smooth the edges with sandpaper thoroughly.

Fitting the base beams

Fitting the base beams

Fit the beams to the posts and use a spirit level to make sure they are perfectly horizontal. Clamp the beams to the posts and drill pilot holes. Insert 9″ carriage bolts to lock everything with attention. Use washers on both beams.

Support beams

Support beams

Buy 2×8 lumber for the support beams, as well. Make decorative cuts to both ends of the beams, using the pattern shown above.

Fitting the support beams - 12x14 Pergola

Fitting the support beams – 12×14 Pergola

Continue the project by fitting the beams to the pergola, perpendicular to the base beams. Center the beams to the top of the posts, leaving equal 12″ overhangs on both sides. Drill pilot holes through the beams and through the posts and insert 9″ carriage bolts. Make sure you plumb the posts again, before attaching the support beams. All corners should also be right angled.

Rafters-for-12x14-pergola

Rafters-for-12×14-pergola

Next, use 2×6 lumber for the rafters. As you can see in the plans, you need to make a few slots to the beams so you can lock them to the support beams. Make parallel cuts inside the marked areas and then remove the excess with a chisel.

Rafter end - Decorative cut

Rafter end – Decorative cut

Also, use a jigsaw to make the curved cuts to both ends of the rafters. Make the straight cuts with a jigsaw.

Fitting-the-rafters-to-the-12x14-pergola

Fitting-the-rafters-to-the-12×14-pergola

Fit the rafters to the top of the pergola frame. Place the rafters equally spaced, as shown in the diagram. Use rafter ties or just drill pilot holes and insert 5 1/2″ screws to lock the rafters to the supports beams.

 

Fitting the rafters

Braces for pergola

Braces for pergola

Furthermore, use 6×6 lumber for the braces. Use a saw to make 45 degree cuts at both ends of the pieces. Get a jigsaw to make the curved cuts that will enhance the look of the backyard pergola. These braces will reinforce the structure of the pergola and make it much more stable to high winds.

Fitting the braces - 12x14 Pergola

Fitting the braces – 12×14 Pergola

Next, use a spirit level to plumb the posts and then fit the braces into place, as shown in the diagram. Drill pilot holes and insert 5 1/2″ screws to secure the braces into place tightly. Use at least 2 screws for each joint. Make sure there are no gaps between the components, when attaching the braces.

Fitting the top slats

Fitting the top slats

Also, fit the 1×2 slats to the top of the pergola. Place these slats equally spaced for a professional result. Make sure the overhangs are equal. Center the slats to the rafters and then drill pilot holes, before inserting the 1 5/8″ screws. If installed properly, these slats will keep the rafters equally spaced on the long run.

 

Finishing touches

12x14-pergola-plans

12×14-pergola-plans

Last but not least, you need to take care of the finishing touches. Therefore, fill the holes with wood putty and then smooth the surface with 120-220 grit sandpaper. Apply a few coats of paint or stain over the components, to enhance the look of the patio pergola and to protect the components from decay.

DIY 12x14 Pergola

DIY 12×14 Pergola

Also, this pergola has a stylish design so you shouldn’t be worried that it might not fit the design of your property. In addition, you should adjust the distance between the shade elements to create the amount of shade you desire.

How to build a 12x14 pergola - diy

How to build a 12×14 pergola – diy

If you want to add charm and unique appeal to your garden, I recommend you to check out these plans. This pergola can be built by any person with basic woodworking skills and it is also very budget friendly. You can make a lot of adjustments to the design so it suits your tastes and needs. Check out the rest of my pergola plans, as I have many designs and sizes you can choose from. In addition, I have over 1500 free woodworking plans on the blog, if you need more building inspiration. See HERE a list with all my free plans.

 

 

This woodworking project was about 12×14 pergola plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

 

- EXPLORE MORE IDEAS FOR -

You may also like

6 comments

Sam Miller -

page 3 incorrect measurements? and diagram for 12×14 pergola please send me correct measurements by e mail and correct plans on web site

Reply
Nick Melnyk -

I have a question about the materials section. Is some if the information from the diagram materials duplicated below it? i.e what is the difference regarding above the line and below?

Reply
Ovidiu -

A, B, C is the Cut list. The below list is the Shopping list.

Reply
Marc -

I would like to cover this pergola with polycarbonate sheets. Would this structure support the weight of a snow fall? Thanks

Reply
jake hancock -

I have been looking to build this in our backyard, and was curious to if I would be able to use the Simpson strong tie accent collection where the 2×8’s meet the 6×6’s. rather than a carriage bolt. thanks!

Reply
Ovidiu -

Yes, you can do that

Reply

Leave a Comment