10×14 Run in Shed Roof Plans

This step by step diy woodworking project is about 10×14 run in shed roof plans. This article is PART 2 of the run in shed project, where I show you how to frame the lean to roof and how to fit the decorative trims. Make sure you check out the rest of plans to see alternatives and more projects for your garden.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.

Projects made from these plans

10×14 Run in Shed Roof Plans

Building-a-10×14-run-in-shed

Cut & Shopping Lists

• E – 3 pieces of T1-11 siding – 48″x91 1/2″ long, 1 piece – 24″x91 1/2″ long, 2 pieces – 24″x120 long, 2 pieces – 2 pieces – 48″x120″ long, 2 pieces – 48″x108″ long SIDING
• F – 12 pieces of 2×6 lumber – 144″ long, 2 pieces of 2×4 lumber – 11 1/4″ long, 2 pieces – 23 3/4″ long RAFTERS
• G – 3 pieces of 3/4″ plywood – 48″x96″ long, 3 pieces – 48″x72″ long ROOF SHEETS
• H – 200 sq ft of tar paper, 200sq ft of asphalt shingles ROOFING
• I – 2 pieces of 2×8 lumber – 144″ long, 2 pieces – 172 3/4″ long TRIMS

• 12 pieces of 2×6 lumber – 12′
• 2 pieces of 2×8 lumber – 12′
• 2 pieces of 2×8 lumber – 16′
• 1 piece of 2×4 lumber – 8′
• 6 pieces of 3/4″ plywood – 4’x8′
• 5 pieces of T1-11 siding – 4×10′
• 200 sq ft of tar paper
• 200 sq ft of asphalt shingles
• 2 1/2″ screws, 3 1/2″ screws, 1 5/8″ screws

Tools

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

Time

 One day

Building a 10×14 shed plans

Rafters

Build the rafters from 2×4 lumber. Make a notch to the rafters, using the information from the diagram. Smooth the recess with a damp cloth.

Fitting-the-rafters

Fit the rafters to the top of the shelter. Drill pilot holes and lock the rafters to the structure with screws and rafter ties. Place the rafters every 16″ on center.

Side roof supports

Use 2×4 lumber for the side lean to roof supports. Make the angle cuts with a miter saw and then lock them into place tightly with screws.

Back wall siding sheets

Attach 4’x8′ T1-11 siding to the back wall of the shelter. Use 1 5/8″ brad nails to lock the sheets into place tightly. Insert the nails every 8″ along the wall framing.

Side panels

Continue the project by fitting the panels to the sides of the shed. Make the cuts so you can fit the panels into place tightly. Insert 6-8d nails, every 8″ along the framing.

Fitting-the-roof-sheets

Attach 3/4″ plywood sheets to the rafters, using the pattern shown in the diagram. Drill pilot holes and insert 1 5/8″ screws, every 8″ along the rafters.

Roof trims

Fit the 2×8 trims to the sides, to the front and to the back of the shed. Cut the components at the right dimensions and then align them into place with attention. Drill pilot holes and then insert 3 1/2″

Fitting the roofing

Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. Secure the tar paper to the plywood sheets with roofing staples. In addition, cut a 12″ piece for the top ridge. Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under.

10×14 Run In Shed Plans – Front view

The shelter seen from one side has a nice appearance. Make sure there are no gaps between the sheets.

10×14 Run In Shed Plans

Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-200 grit sandpaper and remove the residues with a damp cloth.

Top Tip: Check out PART 1 of the project, to learn how to build the frame for the  10×14 run in shed.

This woodworking project was about 10×14 run in shelter plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

- EXPLORE MORE IDEAS FOR -