Home Shed 16×24 Gable Shed Roof Plans

16×24 Gable Shed Roof Plans

by Ovidiu

 

This step by step diy project is about 16×24 gable shed roof plans.This is PART 2 of the gable shed project, where I show you how to build the gable roof for this shed. The roof is sturdy and it will drain the water properly. Make sure you read the local codes so you can comply with the legal requirements. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.

 

 

Projects made from these plans

Add-image

 

 

16×24 Gable Shed Roof Plans

Building-a-16x24-shed-gable-roof

Building-a-16×24-shed-gable-roof

 

Cut & Shopping Lists

  • G – 8 pieces of T1-11 siding – 34 1/2″x48 long, 4 pieces – 48″x62 1/4 long SIDING
  • H – 26 pieces of 2×6 lumber – 120″ long, 13 pieces – 192″ long TRUSSES
  • H – 4 pieces of 2×4 lumber – 9 3/4″ long, 4 pieces – 37 1/2″ long, 26 pieces – 23 1/2″ long, 13 pieces – 50 1/4″ long SUPPORTS
  • I – 10 pieces of 3/4″ plywood – 48″x96″ long, 4 pieces – 48″x48″ long, 6 pieces – 24″x96″ long, 4 pieces – 10 3/4″x24″ long, 4 pieces – 10 3/4″x96″ long ROOF
  • J – 4 pieces of 2×6 lumber -120″ long, 14 pieces – 7″ long  2xOVERHANGS
  • J – 550 sq ft of tar paper, 550 sq ft of asphalt shingles ROOFING
  • K – 2 pieces of 1×8 lumber – 309 1/4″ long, 1 piece – 192″ long, 4 pieces – 121 1/4″ long TRIMS

Tools

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

Time

 One day

Related

 

 

How to build a 16×24 gable shed roof

Building-the-rafters

Building-the-rafters

First of all, you need to build the regular rafter for the shed. Cut one end of the 2×6 rafters at 60 degrees and smooth the edges with sandpaper.

Bottom-rafters

Bottom-rafters

The next step of the project is to build the bottom rafter from 2×6 lumber. Cut both ends of the beams at 30 degree. The easiest method is by using a good miter saw. Lay all the components on a level surface and leave no gaps between them .

Fitting the supports

Fitting the supports

Use 2×4 lumber for the supports. Cut one end of the supports at 60 degrees and then lay them on the level surface.

Gussets

Gussets

Make 1/2″ plywood gussets and lay them over the joints. Leave no gaps between the components and insert 1 5/8″ screws so you can lock all the components together tightly. These will be the trusses for the end panels. You need all these supports, so you can safely attach the siding panels.

Regular Trusses

Regular Trusses

For the regular trusses, you should follow this pattern. Fit the 1/2″ plywood gussets accordingly and lock them to the rafters with 1 5/8″ screws.

Fitting-the-trusses---16x24-gable-shed

Fitting-the-trusses—16×24-gable-shed

Fit the trusses to the top of the 16×24 shed. Place the trusses evenly, by installing them every 24″ on center. Use a spirit level to plumb the trusses and use ties to lock them to the top plates.

Gable end panels

Gable end panels

Cut the gable end panels from T1-11 siding and then secure them into place with 6-8d nails. Leave no gaps between the sheets for a professional result.

Assembling the overhangs

Assembling the overhangs

Assemble the overhangs for the front and back of the shed by using regular rafters and 2×6 blockings. Drill pilot holes through the rafters and insert 3 1/2″ screws into the overhangs.

Fitting the overhangs

Fitting the overhangs

Fit the overhangs to the front and to the back of the shed. Align the edges with attention, drill pilot holes and insert 3 1/2″ screws.

Fitting the roof sheets

Fitting the roof sheets

Use 3/4″ plywood for the roof sheets. Cut all the panels at the right size, as shown in the diagram and then lay them to the top of the roof. Align the edges with attention, drill pilot holes and insert 1 5/8″ screws to lock them into place, every 8″ along the rafters. Leave no gaps between the sheets for a professional result.

Fitting the side roof trims

Fitting the side roof trims

Fit 1×8 trims to the sides of the shed. Align the edges with attention and insert 2″ brad nails to lock the trims into place tightly.

Fitting the front and back trims

Fitting the front and back trims

Build the trims for the front and for the back of the 16×24 gable shed. Align the edges and insert 2″ brad nails so you can set the trims into place.

Fitting the roofing

Fitting the roofing

Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. Secure the tar paper to the plywood sheets with roofing staples. In addition, cut a large piece for the top ridge. Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under.

Read the instructions labeled on the asphalt shingle packs before installing them into place tightly. Start with the bottom left side of the roof and install them all the way to the top.

16x24 Shed Plans - Front view

16×24 Shed Plans – Front view

Don’t forget to take a look over PART 1 and PART 3 to learn how to build the frame for the shed, as well as how to frame the double front doors. If you are looking for a different design, make sure you take a look over all my shed plans HERE.

 

 

This woodworking project was about 16×24 gable shed plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

 

Previous Next

 

 

 

EXPLORE MORE IDEAS FOR:

You may also like

9 comments

Bradley -

I was getting together the materials listing for all parts, and I noticed that the “20 pieces of 2×4 lumber” section in the list doesn’t have the length of the boards. do they need to be 12′, 16′ ? Thank you! Looking forward to building this shed. My was just recently crushed by a falling tree. Have to get a replacement built.

Reply
Julian -

8’long. The 2x4s are for the truss supports. Good luck with the project.

Reply
Marc Reinhardt -

Can you do a plan for the same shed with a 12ft loft same hight and only a double door with windows and no second door??

Reply
Ovidiu -

I don’t design custom plans. You can easily make these modifications by yourself, although I consider the roof height is too low for a loft that size.

Reply
Dyshorn Lebron -

What is a good price estimate for all the materials?

Reply
Ovidiu -

$4000

Reply
Mark Stantz -

I am going to build a 16′ X 24″ shed/garage for my work shop/tractor storage. I am happy with your plans, but I am have a foundation poured so I don’t need the subfloor. Is it possible to purchase just the building direction and material list for just the building?

Mark Stantz

Reply
Ovidiu -

You don’t have to purchase anything. There are no Premium Plans for this design at the moment. You can get these free plans here: https://myoutdoorplans.com/faq/ You will have to substract the materials for the floor.

Reply
Donald -

I am about to start on a 16×24 gable shed using your plans. Is there a need for a drip edge between the lower siding and the upper gable siding?

Reply

Leave a Comment