This step by step diy project is about 14×16 lean to shed roof plans. This is PART 2 of the lean to shed project, where I show you how to build the rafters and hot to fit the roof trims. This shed ha a small slope, so I recommend you to read the local codes to make sure it complies with the local codes. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. See all my Premium Plans HERE.
Projects made from these plans
14×16 Lean to Shed Roof Plans
Cut & Shopping Lists
- H – 2 pieces of T1-11 siding – 13 1/2″x48″ long, 2 pieces – 25 1/2″x48″ long, 2 pieces – 33 1/2″x48″ long, 2 pieces – 17 1/2″x24″ long, 2 pieces of 2×4 lumber- 6 3/4″ long, 2 pieces – 10 3/4″ long, 2 pieces – 18 3/4″ long SIDING
- I – 9 pieces of 2×4 lumber – 192″ long RAFTERS
- J – 2 pieces of 2×4 lumber – 192″ long, 7 pieces – 9″ long 2xOVERHANG
- K – 4 pieces of 3/4″ plywood – 12 3/4″x96″ long, 6 pieces – 48″x96″ long, 4 pieces – 48″x48″ long ROOF
- L – 2 pieces of 1×8 lumber – 192″ long, 2 pieces – 218 3/4″ long TRIMS
- M – 300 sq ft of tar paper, 300 sq ft of asphalt shingles ROOFING
- 15 pieces of 2×6 lumber – 16′
- 2 pieces of 2×4 lumber – 8′
- 2 pieces of T1-11 siding – 4’x8′
- 2 pieces of 1×8 lumber – 18′
- 2 pieces of 1×8 lumber – 16′
- 10 pieces of 3/4″ plywood – 4’x8′
- 300 sq ft of tar paper, 300 sq ft of asphalt shingles
- 8d nails, 2 1/2″ screws, 3 1/2″ screws
- wood filler , wood glue, stain/paint
- PART 1: 14×16 Lean to Shed Plans
- PART 2: 14×16 Lean to Shed Roof Plans
- PART 3: 14×16 Lean to Shed Door Plans
Building a 14×16 Lean to Shed Roof
Build the rafters for the shed from 2×6 lumber. Cut the rafters at the right dimensions and angles using a saw. Lay the rafters on a level surface and align the edges with attention.
Fit the trusses to the top of the shed, making sure you place them every 24″ on center. Use rafter ties to lock the trusses into place tightly. Align everything with attention, for a professional result.
Fit the 2×4 supports to the sides of the lean to shed, as shown in the diagram. Cut the supports at the right dimensions and angles and drill pocket holes at both ends. Use 2 1/2″ screws to lock the supports into place tightly.
Fit T1-11 siding panels to the gable ends. Mark the cut lines on the panels and then lock them into place with 6d nails. Leave no gaps between the panels.
Next, you need to assemble the overhangs for the shed. Drill pilot holes through the rafters and insert 2 1/2″ screws into the blockings. You can easily adjust the size of the overhangs to suit your needs.
Fit the overhangs to the sides of the shed. Align the edges, drill pilot holes and insert 3 1/2″ screws to lock them into place tightly.
Cut the sheets for the roof from 3/4″ plywood and then fit them to the top of the shed. Align the edges with attention, drill pilot holes and insert 1 5/8″ screws, every 8″ along the rafters. Leave no gaps between the sheets for a professional result.
Fit the 1×8 trims to the sides of the roof. Align the trims with attention and insert 2″ nails. Fit the 1×8 trims to the front and back of the roof. Align the edges and insert 2″ nails, every 8″ along the framing.
Cover the roof with tar paper and then install the asphalt shingles. Make sure you also install the appropriate drip edges, so you can seal the shed roof. Read the manufacturer’s instructions for a tight fit.
I have lots of other shed projects on the site so I recommend you to browse through all alternatives before starting the building project. See all my shed projects HERE. Moreover, check out PART 1 of the shed, so you learn how to build the frame of the shed. Check out PART 3 to learn how to build the doors and how to fit the decorative trims.
This woodworking project was about 14×16 lean to shed roof plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.