This step by step diy project is about free 10×20 run in shed plans with drawings. This is a relatively large run in shed that can be built on a budget, using basic materials and tools. The roof has a 2:12 pitch and features a large opening, for easy access. This shed is ideal for 2 horses. Read the local codes before starting the project, so you comply with the legal requirements. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.
Projects made from these plans
10×20 Run In Shed Plans – Free PDF Download
- A – 6 pieces of 4×4 lumber – 113″ long, 3 pieces – 93″ long POSTS
- B – 3 pieces of 4×4 lumber – 113″ long, 2 pieces – 114 3/4″ long, 3 pieces – 17″ long BASE
- C – 2 pieces of 2×4 lumber – 113″ long, 9 pieces – 96″ long 2xSIDE WALL
- D – 2 pieces of 2×4 lumber – 114 3/4″ long, 9 pieces – 86 1/2″ long 2xBACK WALL
- E – 2 pieces of 2×4 lumber – 113″ long, 7 pieces – 38 1/2″ long MIDDLE WALL
- E – 2 pieces of 2×4 lumber – 17″ long, 3 pieces – 106 1/2″ long 3xFRONT WALL
- G – 3 pieces of T1-11 siding – 48″119 long, 5 pieces – 48″x99″ long, 2 pieces – 10″x48″ long SIDING
- 4 pieces of 4×4 lumber – 8′
- 11 pieces of 4×4 lumber – 10′
- 8 pieces of 2×10 lumber – 10′
- 19 pieces of 2×4 lumber – 10′
- 42 pieces of 2×4 lumber – 8
- 8 pieces of 5/8″ T1-11 siding – 4’x10′
- 2 pieces of 1/2″ plywood – 4’x8′
- corner brackets
- 2 1/2″ screws, 3 1/2″ screws, 1 5/8″ screws
- 6d nails
- concrete form
- post anchors
- post to beam connector
- wood filler , wood glue, stain/paint
- heavy duty glue
- PART 1: 10×20 Run in Shed Plans
- PART 2: 10×20 Run in Roof Shed Plans
Building a 10×20 run in shed
The first step of the project is to layout the posts for the run in shed and to set them into place. Dig 3′ deep 12″ in diameter holes for the concrete footings. Set the concrete forms and then fill them with concrete. Set the post anchors, making sure they are aligned properly. After a few days, set the 4×4 posts into place with lag screws and temporarily braces,
Use 4×4 skids between the posts. Drill pocket holes at both ends and insert 2 1/2″ screws to secure them to the posts (on both sides). Make sure the corners are square and align the edges flush.
Use 2×10 beams and 1/2″ plywood to make the back wall headers. Use heavy duty glue and 2 1/2″ screws to assemble the beams.
Fit the beams to the top of the posts. Use connectors to secure the beams to the posts. Make sure the posts are plumb and check if the corners are square. Align everything with attention.
Building the wall frames
Next, you have to build the side wall frames from 2x4s. Cut the plates and the studs as shown in the diagram. Drill pilot holes through the plates and insert 3 1/2″ screws into the studs. Place the studs every 16″ on center. Make sure the corners are square.
Assemble the two sections for the back wall using the info from the diagram and the techniques described above.
Assemble the frames for the front wall. Drill pilot holes through the plates and insert 3 1/2″ screws into the studs. Make sure the corners are square.
Fit the wall frames between the posts and align the edges flush. Drill pilot holes and insert 3 1/2″ screws through the wall frames into the skids, posts and headers.
Use 2×4 lumber for partition. Drill pilot holes through the plates and insert 3 1/2″ screws into the studs. Place the studs equally spaced.
Fit the wall frame to the middle of the run in shed. Align the edges flush, drill pilot holes and insert 3 1/2″ screws into the skid and into the front and wall frames.
Fitting the shed siding sheets
Cut and fit the T1-11 siding sheets to the front of the shed, as shown in the plans. Cut the sheets at the right dimensions and then attach them to the framing with 6d nails, every 8″ along the studs and plates.
Fit the 5/8″ siding sheets to the back of the shed. Align the edges with attention and leave no gaps between them for a professional result. Use 6d nails, every 8″ along the framing, to secure the sheets into place tightly.
This 10×20 loafing shed is extremely versatile when it comes to uses. You can use it for animals for firewood or for equipment and machinery.
Check out PART 2 of the 10×20 run in shed project project to learn more on how to build the lean to roof structure. I have tons of other woodworking plans, so you should check out the whole list HERE. If you want to get this project as a PDF file, with 1 full Cut list and 1 full Shopping list, please take a look over the GET PDF PLANS button bellow.
This woodworking project was about 10×20 run in shed plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.