This step by step diy project is about 10×16 hip roof shed plans. This is PART 2 of the shed project where I show you how to build the roof structure for the 10×16 shed. I show you all you need to know about framing a beautiful hip roof. If you want a shed with a hip roof to match your house design check out my free instructions. Make sure you read the local codes so you can comply with the legal requirements. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.
Projects made from these plans
10×16 Hip Roof Shed Plans
[tabs tab1=”Materials” tab2=”Tools” tab3=”Time” tab4=”Related Plans”] [tab id=1]
- I – 2 pieces of 2×4 lumber – 40″ long, 1 piece of 2×6 lumber – 73 1/2″ long, 2 pieces – 36″ long RIDGE BEAM
- J – 4 pieces of 2×6 lumber – 110 1/2″ long HIP RAFTERS
- K – 16 pieces of 2×6 lumber – 86 1/2″ long COMMON RAFTERS
- L – 8 pieces of 2×6 lumber – 29 1/2″ long, 8 pieces – 48 3/4″ long, 8 pieces – 67 3/4″ long JACK RAFTERS
- M – 6 pieces of 3/4″ plywood – 48″x70″ long, 4 pieces – 29 3/4″x35″ long, 4 pieces – 48″x71″ long, 4 pieces – 30 3/4″x34 3/4″ long, 2 pieces – 34 3/4″x70″ long ROOF SHEETS
- N – 300 sq ft of tar paper, 300 sq ft of asphalt shingles ROOFING
- O – 2 pieces of 1×8 lumber – 141 1/4″ long, 2 pieces – 211 3/4″ long TRIMS
- 1 piece of 2×4 lumber – 8′
- 34 pieces of 2×6 lumber – 8′
- 4 pieces of 2×6 lumber – 10′
- 13 pieces of 3/4″ plywood – 4’x8′
- 2 pieces of 1×8 lumber – 12′
- 4 pieces of 1×8 lumber – 10′
- 300 sq ft of tar paper, 300 sq ft of asphalt shingles
- 2 1/2″ screws, 3 1/2″ screws, 1 5/8″ screws
- 6d nails, 8d nails
- wood filler , wood glue, stain/paint
[/tab] [tab id=2]
Hammer, Tape measure, Framing square, Level
Miter saw, Drill machinery, Screwdriver, Sander
[/tab] [tab id=3]
- PART 1: 10×16 Shed with a Hip Roof Plans
- PART 2: 10×16 Hip Roof Shed Plans
- PART 3: Door Plans for 10×10 Shed
It’s that simple to build a shed with a hip roof – Video!
10×16 Shed Hip Roof Plans
The first step of the project is to install the ridge beam for the hip roof. Therefore, use 2×4 lumber for the supports and drill pocket holes at both ends. Use 2×6 lumber for the ridge beams. Center the supports to the plates and insert 2 1/2″ screws to lock everything together tightly. Plumb the supports and make sure the corners are square.
Use 2×6 lumber for the braces and make 45 degree cuts to both ends. Drill pocket holes at both ends of the braces. Fit the braces to the ridge beams and insert 2 1/2″ screws to lock them into place tightly.
Use a miter saw to make 25 degree cuts to both ends of the boards. These are the hip rafters. Smooth the edges with sandpaper. Make sure you do a compound cut to the top end of the hip rafters (48 degrees bevel, 25 degrees miter).
Fit the hip rafters to the storage shed. Align the edges with attention, drill pilot holes and insert 3 1/2″ screws to lock them into place tightly. Use rafter ties to reinforce the joints.
Use 2×6 lumber for the common rafters. Use a miter saw to make the 33.5 degree angle cuts to both ends of the rafters, as shown in the diagram.
Fit the common rafters to the top of the 10×16 shed. Align the edges, drill pilot holes and insert screws to lock them into place tightly. Fit the rafters every 16″ on center, as shown in the plans.
Next, build the jack rafters for the hip roof of the shed. Use a miter saw and make a simple 33.5 degree miter cut at one end. Use the miter and make a compound cut for the opposite end: 33.5 miter cut and 50 degree bevel cut.
Fit the jack rafters to the top of the shed. Start installing the jack rafters from the common rafters toward outside, every 16″ on center. Use rafter ties to the secure the rafters into place tightly. Drill pilot holes and insert
This is basically the roof structure for a hip shed.
Use 3/4″ plywood for the roof sheets. Cut the sheets at the right dimensions and then lay them to the top of the roof structure. Align the edges flush, leave no gaps between the sheets and insert 1 5/8″ screws, every 8″ along the framing.
Fit the sheets to the sides of the roof.
Use 1×8 lumber for the roof trims. Cut the trims at the right dimensions and secure them to the end of the rafters. Drill pilot holes and insert 2 1/2″ screws to lock the trims into place tightly.
Install the roofing felt, starting from the bottom left of the roof. Secure the paper to the roofing, using a stapler. Make sure the tar paper overlaps at least 2”. Don’t forget to cover the top ridge with a 14” strip of paper .
Start the first course of shingles with a full tab, the second with 2 1/2 tabs, the third with 2 tabs, the forth with 1 1/2 tabs, the fifth with 1 tab, the sixth with half tab and the seventh with a 3 tabs.
Make sure you check out PART 1 and PART 3 of the hip roof shed project, so you learn how to build the wall frames and the door.
This 10×16 shed is beautiful, sturdy and it has a lot of room for storage. You can make a lot of adjustments and customize it to suit your needs. Please take a look over the rest of my woodworking plans, because I have over 1500 free designs.
This woodworking project was about 10×16 shed with hip roof plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.