This step by step diy project is about 10×16 shed doors and trims plans. This is PART 3 of the 10×16 lean to shed project, where I show you how to build the double doors for the storage shed and how to fit the decorative trims. Take a look over the rest of my woodworking plans, if you want to get more building inspiration. Remember that you need to select the site for the shed with attention and that you have to comply with a few legal regulations.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.
Projects made from these plans
10×16 Lean to Shed Doors Plans
[tabs tab1=”Materials” tab2=”Tools” tab3=”Time” tab4=”Related Plans”] [tab id=1]
- J – 2 pieces of 2×4 lumber – 103″ long, 1 piece – 75 1/2″ long JAMBS
- K – 1 piece of T1-11 siding – 48″x75 1/2″ long, 2 pieces of 2×4 lumber – 48″ long, 2 pieces – 75 1/2″ long, 1 piece – 41″ long 2xDOOR
- L – 2 pieces of 1×4 lumber – 108″ long, 1 piece – 186 1/4″ long, 2 pieces – 107″ long, 2 pieces – 82 1/2″ long, 2 pieces – 115″ long, 2 pieces – 42 1/2″ long, 2 pieces – 83″ long TRIMS
- 1 piece of 2×4 lumber – 10′
- 9 pieces of 2×4 lumber – 8′
- 2 pieces of T1-11 siding – 4’x8′
- 1 piece of 1×4 lumber – 16′
- 5 pieces of 1×4 lumber – 8′
- 6 pieces of 1×4 lumber – 10′
- 2 1/2″ screws, 3 1/2″ screws, 1 5/8″ screws
- 4d nails, 16d nails, 6d nails
- wood filler , wood glue, stain/paint
[/tab] [tab id=2]
[/tab] [tab id=3]
Building the double shed doors
Fit the 2×4 jambs around the opening with 2 1/2″ screws. Insert the screws every 8″ along the framing. Align the edges flush.
Build the door panels from T1-11 siding and the trims from 2×4 lumber. Use 2″ screws to lock the panels to the trims. Add glue to the joints and align the edges flush.
Fit the doors to the opening and align the edges with attention. Install hinges to lock the doors to the jambs tightly. Install a latch so you can lock the doors together tightly.
Fit the 1×4 trims to the back of the shed. Use 6-8d nails to lock the trims into place, every 8″ along the framing.
Fit the 1×4 decorative trims to the sides of the shed, as well. Cut the trims at the right dimensions and then lock them into place with 2″ nails.
Fit the decorative trims to the front of shed. Align the edges with attention and then insert 2″ nails, every 8″, so you can lock them into place tightly.
Last but not least, you need take care of the finishing touches. Fill the holes with wood putty and then smooth the surface with 120-220 grit sandpaper. Apply a few coats of paint or stain to the components, so you can protect them from decay and so you can enhance the look of the shelter. Check out PART 1 and PART 2 of the shed, so you can learn everything you need to know about building the floor, walls and roof for the shed.
This woodworking project was about shed doors plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.