Home Shed 10×12 Lean to Shed Plans – Part II

10×12 Lean to Shed Plans – Part II

by Ovidiu

 

This step by step diy project is about diy 10×12 lean to shed roof plans. This is PART 2 of the lean to shed project, where I show you how to build the lean to roof for the 10×12 shed. Moreover, I have designed shed with many sizes so check them out, as well. Roof pitch is 2:12. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.

 

 

Projects made from these plans

Add-image

 

 

10×12 Lean to Shed Plans – Part II

Building-a-10x12-lean-to-shed

Building-a-10×12-lean-to-shed

 

Cut & Shopping Lists

  • H – 2 pieces 5/8″ T1-11 siding – 48″x120″ long, 2 pieces – 48″x112″ long, 2 pieces – 24″x104″ long SIDING
  • I – 10 pieces of 2×6 lumber – 144″ long RAFTERS
  • J – 4 pieces of 2×6 lumber – 144″ long, 7 pieces – 6 1/2″ long OVERHANGS
  • K – 3 pieces of 1/2″ plywood – 4’x8′ long, 3 pieces – 4’x4′ long, 2 pieces – 10″x96″ long, 2 pieces – 10″x48″ long ROOF
  • L – 2 pieces of 1×8 lumber – 12 ft long, 2 pieces – 165 1/2″ long ROOF TRIMS
  • M – 180 sq ft of tar paper, 180 sq ft of asphalt shingles ROOFING
  • N – 2 pieces of 2×4 lumber – 80″ long, 1 piece – 79″ long JAMBS
  • O – 2 pieces of 2×4 lumber – 73″ long, 2 pieces – 36″ long, 1 piece – 29″ long, 1 piece of T1-11 siding – 36″x80″ long 2xDOOR
  • P – 4 pieces of 1×4 lumber – 114″ long, 4 pieces – 94 1/4″ long, 2 pieces – 36″ long, 2 pieces – 43″ long TRIMS

Tools

 Hammer, Tape measure, Framing square, Level, Pocket hole jig

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

Time

 One day

Related

 

 

Building a 10×12 lean to roof

Rafters-for-10x12-lean-to-shed

Rafters-for-10×12-lean-to-shed

Build the rafters from 2×6 lumber. Mark the cut lines on the slats and get the job done with a circular saw.

Fitting-the-rafters

Fitting-the-rafters

Fit the rafters to the top of the lean to shed. Place the rafters every 16″ on center and lock them into place with rafter ties and 1 1/2″ structural screws.

Side wall panels

Side wall panels

Cut the panels for the lean to ends and secure them into place with 6-8d nails. Leave no gaps between the panels for a neat result.

Overhangs

Overhangs

Assemble the side overhangs from 2×6 lumber. Drill pilot holes through the sides and insert 3 1/2″ screws into the blockings.

Fitting the side overhangs

Fitting the side overhangs

Fit the blockings to the sides of the shed, align the edges flush and secure them into place with 3 1/2″ screws.

Roof-sheets

Roof-sheets

Lay the 3/4″ plywood sheets to the top of the shed starting with the bottom of the roof. Use 1 5/8″ screws to secure the sheets into place, every 8″ along the rafters.

Fitting-the-side-roof-trims

Fitting-the-side-roof-trims

Fit the 1×8 trims to the sides of the shed. Align the edges flush, leave no gaps between the boards and then lock them into place with 2″ nails.

Roof trims

Roof trims

Fit the 1×8 trims to the front of the shed. Align the edges flush, leave no gaps between the boards and then lock them into place with 2″ nails.

Fitting the roofing

Fitting the roofing

Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. Secure the tar paper to the plywood sheets with roofing staples. Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under.

Fitting the door jambs

Fitting the door jambs

Use 2×4 lumber for the door jambs. Fit the door jambs around the door and then secure them into place with 3 1/2″ screws.

Shed-door-frame

Shed-door-frame

Use 2×4 lumber for the door frame. Drill pocket holes at both ends of the vertical and middle components. Align the edges flush and insert 2 1/2″ screws to assemble the door frame.

Door panel

Door panel

Use T1-11 siding sheets for the door panel. Align the edges flush and insert 1 5/8″ screws to secure the panel to the frame. Add glue to the joints.

Fitting the double doors

Fitting the double doors

Fit the doors to the opening and then align the edges flush. Use hinges to secure the doors to the jambs. Also, set a latch so you can keep the doors locked.

Fitting the corner trims

Fitting the corner trims

Fit the PVC window to the side of the shed and then install the decorative trims. In addition, fit the 1×4 trims to the corners of the shed. Align the edges flush and insert 2″ nails to lock them into place tightly.

10x12 Lean to shed MOP

10×12 Lean to shed MOP

 

10x12 Lean to shed - overall dimensions

10×12 Lean to shed – overall dimensions

Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-220 grit sandpaper and remove the residues with a damp cloth.

Top Tip: Apply a few coats of paint or stain to the components, to enhance the look of the project. Check PART 1 of the project to learn how to build the frame of the shed.

 

 

This woodworking project was about 10×12 lean to shed roof plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

 

Previous

 

 

 

EXPLORE MORE IDEAS FOR:

You may also like

Leave a Comment