10×12 Barn Shed Roof Plans

This step by step diy project is about 10×12 barn shed roof plans. This is PART 2 of the storage shed project, where I show you everything you want to know about framing the barn shaped roof. Take a look over the rest of my woodworking plans, if you want to get more building inspiration. Remember that you need to select the site for the shed with attention and that you have to comply with a few legal regulations.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.



Projects made from these plans




10×12 Barn Shed Roof Plans




[tabs tab1=”Materials” tab2=”Tools” tab3=”Time” tab4=”Related Plans”] [tab id=1]

  • H – 4 pieces of T1-11 siding – 48″x57 1/4″ long, 2 pieces – 24″x62 1/4″ long SIDING
  • I – 28 pieces of 2×6 lumber – 48″ long TRUSSES
  • J – 8 pieces of 2×6 lumber – 48″ long, 16 pieces – 4 1/4″ long 2xOVERHNAG
  • K – 4 pieces of 2×4 lumber – 50 1/2″ long SUPPORTS
  • K – 4 pieces of 3/4″ plywood – 48″x96″ long, 4 pieces – 48″x48″ long, 8 pieces – 8″x48″ long ROOF
  • L – 200 sq ft of tar paper, 200 sq ft of asphalt shingles ROOFING

  • 24 pieces of 2×6 lumber – 8′
  • 2 pieces of 2×4 lumber – 10′
  • 7 pieces of 3/4″ plywood – 4’x8′
  • 1 piece of 1/2″ plywood – 4’x8′
  • 6 pieces of T1-11 siding – 4’x8′
  • 200 sq ft of tar paper, 200 sq ft of asphalt shingles
  • 2 1/2″ screws, 3 1/2″ screws, 1 5/8″ screws
  • 4d nails, 16d nails, 6d nails
  • wood filler , wood glue, stain/paint

[/tab] [tab id=2]

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

[/tab] [tab id=3]

 One day

[/tab][tab id=4]




Trim---Facebook-BoxMake sure you follow me on Facebook to be the first that gets our latest plans and for some other exclusive content. Also, follow me on Pinterest to get many ideas for your backyard from all the internet! Check out our YouTube channel! See how you can Support  Me with no extra costs to you. Trim---Facebook-Box-Down



How to build a 10×12 barn shed roof



The first step of the project is to build the rafters from 2×6 lumber. Use a miter saw to make 22.5 degree cuts at both ends of the rafters.

Making the bird mouths cut

Making the bird mouths cut

Use a saw to make the birdmouths cuts to the base rafters.

Fitting the gussets

Fitting the gussets

Use 1/2″ plywood for the gussets. Mark the cut lines on the plywood sheet and get the job done with a saw. Fit the gussets over the joints and then lock them to the joints with 1 5/8″ screws.



Fit the trusses to the top of the barn shed. Fit the trusses every 24″ on center and then plumb them vertically with a spirit level. Use rafter ties to secure the trusses into place tightly.

Gambrel end supports

Gambrel end supports

Use 2×4 lumber for the gambrel end supports of the barn shed. Make 22.5 degree cuts to one end of the supports and drill pocket holes at both ends. Fit the supports into place and insert 2 1/2″ screws to lock them tightly.

Gambrel end panels

Gambrel end panels

Cut the sheets for the gambrel ends and then lock them to the supports with 6-8d nails, every 8″. Leave no gaps between the sheets for a professional result.

Assembling the front and back overhangs

Assembling the front and back overhangs

The next step of the project is to assemble the overhangs. Drill pilot holes through the rafters and insert 2 1/2″ screws into the blockings.

Fitting the overhangs

Fitting the overhangs

Fit the overhangs to the front and back of the barn shed. Align the edges with attention, drill pilot holes and insert 3 1/2″ screws to lock the overhangs to the shed frame.



Use 3/4″ plywood for the roof of the barn. Cut all the sheets to the right dimensions and then attach them to the roof of the barn shed. Use 1 5/8″ screws to secure the panels into place, every 8″ along the rafters.

Fitting the roofing

Fitting the roofing

Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. Secure the tar paper to the plywood sheets with roofing staples. In addition, cut a large piece for the top ridge. Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under.

Read the instructions labeled on the asphalt shingle packs before installing them into place tightly. Start with the bottom left side of the roof and install them all the way to the top.

10x12 Barn Shed Plans

10×12 Barn Shed Plans

This barn shed is easy to build. Make sure you take a look over PART 1 and PART 3 of the shed project.

10x12 Gambrel Shed - Free DIY Plans

10×12 Gambrel Shed – Free DIY Plans

You need to check out PART 3 of the shed, so you learn how to build the double doors and how to fit the rest of the trims. If you have’t looked over PART 1 yet, I recommend you to do it, as it will show everything you want to know about building the frame of the shed.



This woodworking project was about 10×12 barn shed roof plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.


Previous Next



  1. Larry

Leave a Reply

error: Content is protected !!