Home Shed 10×12 8 ft Short Shed Roof Plans

10×12 8 ft Short Shed Roof Plans

by Ovidiu

 

This step by step diy project is about 10×12 gable shed roof plans. This is PART 2 of the shed project, where I show you how to build the gable roof for the 10×12 short shed. This shed is a good addition to any backyard, as in most cases you don’t need a permit for it. Make sure you read the local regulations before starting the project. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. See all my Premium Plans HERE.

 

 

Projects made from these plans

Add-image

 

 

10×12 8 ft Short Shed Roof Plans

Building-a-8-ft-high-10x12-shed

Building-a-8-ft-high-10×12-shed

 

Cut & Shopping Lists

  • F – 2 pieces of T1-11 siding – 48″x88″ long, 1 piece – 48″x89 3/4″ long, 1 piece – 48″x84 1/8″ long, 1 piece – 24″x18 1/2″ long 2xSIDING
  • G – 20 pieces of 2×4 lumber – 72″ long RAFTERS
  • G – 2 pieces of 2×4 lumber – 6 1/2″ long, 1 piece of 2×6 lumber – 12 ft RIDGE BEAM
  • H – 2 pieces of 1/2″ plywood – 48×96″ long, 2 pieces – 48″x48″ long, 2 pieces – 24″x48″ long, 2 pieces – 24″x96″ long ROOF
  • I – 4 pieces of 2×6 lumber – 73 1/8″ long, 4 pieces of pieces of 1×6 lumber – 74″ long TRIMS
  • J – 180 sq ft of tar paper, 180 sq ft of asphalt shingles ROOFING
  • K – 2 pieces of 2×4 lumber – 71 1/4″ long, 1 piece – 79″ long JAMBS
  • L – 1 piece of T1-11 siding – 36″x70 1/2″ long, 2 pieces of 2×4 lumber – 63 1/2″ long, 2 pieces – 36″ long, 1 piece – 29″ long 2xDOOR
  • M – 4 pieces of 1×4 lumber – 75 3/4″ long TRIMS

Tools

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

Time

 One week

Related

 

 

Building a 10×12 gable shed roof plans

Rafters-for-8-ft-short-shed

Rafters-for-8-ft-short-shed

The first step of the project is to build the rafters for the shirt shed. Mark the cut lines to both ends of the 2×4 slats and then get the job done with a circular saw. Smooth the edges flush.

Fitting the ridge beam

Fitting the ridge beam

Next, fit the ridge beam to the top of the shed. Use 2×4 lumber for the supports and 2×6 lumber for the ridge beam. Drill pocket holes at both ends of the supports and secure them with 2 1/2″ screws to the middle of the front and back wall top plates. Next, attach the 2×6 beam to the top of the supports, using the same 2 1/2″ screws.

Fitting-the-rafters-to-the-short-shed

Fitting-the-rafters-to-the-short-shed

Fit the rafters to the top of the shed. Place the rafters every 16″ on center. Drill pilot holes and insert screws to lock the rafters into place tightly.

Front wall siding sheets

Front wall siding sheets

Use T1-11 siding sheets to the front of the shed. Align the edges flush and leave no gaps between them. Insert 6d nails every 8″ along the framing, to secure the panels into place. Make cuts so you make the opening for the doors.

Back wall siding sheets

Back wall siding sheets

Cut and attach the siding sheets to the back of the shed.

Roof sheets - 10x12 shed

Roof sheets – 10×12 shed

Use 1/2″ plywood for the roof of the shed. Cut the sheets as shown in the diagram and lay them to the top of the shed. Leave no gaps between the sheets and insert 1 5/8″ screws, every 8″ along the framing.

Front and back roof trims

Front and back roof trims

Use 2×6 lumber for the roof trims. Make the angle cuts and then attach the trims into place with 6d nails.

Fitting the trims to the sides of the roof

Fitting the trims to the sides of the roof

Fit the 1×6 trims to the sides of the shed. Align the edges flush and insert 6d nails to lock them into place tightly.

Fitting the roofing to the 10x12 shed

Fitting the roofing to the 10×12 shed

Cover the roof of the shed with tar paper. The attach the roof with asphalt shingles, starting with the bottom part of the shed up to the top ridge. Make sure you read the manufacturer’s instructions, so you install the shingles properly.

Fitting the jambs

Fitting the jambs

Attach the 2×4 jambs around the opening. Align the edges flush, drill pilot holes and insert 2 1/2″ screws to lock them into place tightly.

Door-for-shed

Door-for-shed

Use 2×4 lumber for the door frame. Drill pocket holes and assemble the door frame. Insert 2 1/2″ screws to lock everything into place tightly and make sure the corners are square. Attach the siding panel with screws or nails.

Fitting the double doors - 8x12 short shed

Fitting the double doors – 8×12 short shed

Fit the double doors to the opening. Align the edges and then attach them to the jambs with hinges. Install a latch to keep the doors locked and then things inside the shed safe.

Fitting the trims to the shed

Fitting the trims to the shed

Last but not least, you need to take care of the finishing touches. Use 1×4 lumber for the corner trims. Align the edges and insert 2″ nails to secure the trims into place tightly. Apply a few coats of paint over the exterior of the shed.

10x12-short-shed-plans

10×12-short-shed-plans

I have lots of other shed projects on the site so I recommend you to browse through all alternatives before starting the building project. See all my shed projects HERE. Moreover, check out PART 1 of the shed, so you learn how to build the frame of the shed.

 

 

This woodworking project was about 10×12 gable shed roof plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

 

Previous

 

 

 

EXPLORE MORE IDEAS FOR:

You may also like

5 comments

Paul -

How did you get 59.25 inches for the run on the roof if the span is 120 inches and the ridge board is 2 inches?
Thanks

Reply
Ovidiu -

The diagrams shows 59 1/4″ till the ridge supports. 2×59 1/4″ + 1 1/2 (thickness of 2×4 supports). Read this table for actual size of lumber: https://myoutdoorplans.com/imperial-to-metric-conversion/

Reply
Paul -

Absolutely loving this build. I have never worked with wood and building something like this is way beyond my capabilities. That said I’m following your plans to the t and so far so good. Few adjustments but that’s down to the timber I got delivered. If you would like to see my progress with pictures let me know.
One more question if I may. I’m at the roof part now. What is the slope? 3/12 or 4!12. Thanks again.

Reply
Ovidiu -

The roof pitch is 2 1/2″ : 12. Looking forward to seeing your project.

Reply
Robert Tucker -

Do you have a detaI of the ridge beam support to the ridge beam and the top plates as I see no variation in length of the the raftersL

Reply

Leave a Comment