Home Fort Outdoor Playset with Swing and Slides – Free PDF Download

Outdoor Playset with Swing and Slides – Free PDF Download

by Ovidiu

 

This step by step diy woodworking project is about outdoor playset with swing and slides plans. This kids playset design features two forts joined together by a bridge. In addition, this project features a swing and a climbing wall. Overall, this is a complex project so I split the free drawing in 2 separate Plans. You can make modifications to my plans so it suits your needs. If you enjoy my design, don’t forget to take a look over the rest of my free plans HERE.

There are so many designs and materials to choose from, that we really recommend you to spend some time researching the most suitable plans for your needs. If you still haven’t found what you are looking for, we strongly recommend you to pay attention to these instructions and to check out the related projects, if you want to get more ideas and potential projects for your home and garden. See all my Premium Plans HERE.

 

 

Projects made from these plans

  Add-image

 

 

Kids Playset with Slide Plans

Building-a-playset-with-slides

Building-a-playset-with-slides

 

Cut & Shopping Lists

  • A – 4 pieces of 4×4 lumber – 132″ long, 1 piece – 65″ long POSTS
  • B – 2 pieces of 1×6 lumber – 72″ long, 2 pieces – 48″ long FRAME
  • C – 2 pieces of 2×4 lumber – 48″ long, 3 pieces – 72″ long FRAME
  • D – 13 pieces of 1×6 lumber – 48″ long FLOOR
  • E – 6 pieces of 2×4 lumber – 37 1/2″ long RAFTERS
  • F – 12 pieces of 1×6 – 72″ long, 1 piece of 1×2 lumber – 72″ long ROOF
  • G – 3 pieces of 2×4 lumber – 48″ long, 2 pieces – 72″ long, 2 pieces – 43″ long, 1 piece – 60 3/4″ long,  RAILS
  • H – 21 pieces of 1×4 lumber – 22″ long RAILINGS
  • I – 1 piece of 2×4 lumber – 36″ long, 3 pieces – 24″ long LADDER
  • J – 4 pieces of 4×4 lumber – 96″ long POSTS
  • K – 4 pieces of 1×6 lumber – 48″ long FRAME
  • L – 5 pieces of 2×4 lumber – 48″ long FRAME
  • M – 9 pieces of 1×6 lumber – 41″ long FLOOR
  • N – 5 pieces of 2×4 lumber – 37 1/2″ long, 1 piece – 56 1/2″ long RAFTERS
  • O – 12 pieces of 1×6 lumber – 48″ long, 1 piece of 1×2 lumber – 48″ long ROOF
  • P – 3 pieces of 2×4 lumber- 48″ long, 2 pieces – 11″ long, 2 pieces – 19″ long, 2 pieces – 24″ long4 pieces – 30 1/4″ long RAILS
  • R – 10 pieces of 1×4 lumber – 22″ long RAILINGS

Tools

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Pocket hole jig, Sander

 Safety Gloves, Safety Glasses

Time

 One day

Related

 

 

Kids Playset – Video!

 

Trim---Facebook-BoxMake sure you follow me on Facebook to be the first that gets my latest plans and for some other exclusive content. Also, follow me on Pinterest and on Instagram to get many ideas for your backyard from all the internet! See how you can Support ME with no extra costs to you. Trim---Facebook-Box-Down

 

How to build a wood playground

Frames-for-tall-tower

Frames-for-tall-tower

The first step of the project is to build the frames for the tall tower of the playset. Use 2×4 lumber for the floor frame and 1×6 lumber for the base frame. I recommend you to use 1x6s for the base frame because you can use that later on, as a sandbox. If not, you can use 1x4s or even 2x4s.

Assembling-the-frame-of-the-large-tower

Assembling-the-frame-of-the-large-tower

Next, we are going to attach the frames to the 4×4 posts. Make sure the corners are square and clamp the frames to the posts. Drill pilot holes and insert 3 1/2″ screws for each joint. Use 4 screws for each joint.

Remember that we need to anchor the posts to the ground. You can choose from several options. You can set the posts directly into concrete for about 2 ft, or you can pour concrete footings and use anchors. The plans are designed considering the second option. Plumb the posts with a spirit level. Attach the 4×4 support to one side of the fort, because we’re going to build the bridge on that.

Floor slats - tall tower

Floor slats – tall tower

Use 1×6 lumber for the floor of fort. Place a piece of 1/4″ plywood between the slats to create even gaps. You need the gaps for drainage. Drill pilot holes through the slats and insert 2 1/2″ screws to lock them to the frame tightly.

Rafters-for-tall-tower

Rafters-for-tall-tower

Use 2×4 lumber for the rafters. Make 45 degree cuts to both ends of the rafters.

Fitting the rafters - tall tower

Fitting the rafters – tall tower

Fit the rafters to the top of the posts. Drill pilot holes and insert 3 1/2″ screws to lock them to the top of the posts. In addition, lock the rafters together with screws, after drilling pilot holes.

Roof slats - tall tower

Roof slats – tall tower

Fit 1×6 slats to the top of the roof. Leave no gaps between the slats and add glue to the joints. Drill pilot holes and insert 2 1/2″ screws to lock the slats to the rafters. Fit the 1×2 slat to the top of the roof.

Tall tower - rails part 2

Tall tower – rails part 2

Next, we’ll tackle the railings for the tall fort of the outdoor playset plans. Therefore, use 2×4 lumber for the rails. Drill pilot holes and insert 3 1/2″ screws to lock the rails to the frame of the fort, as shown in the diagram.

Rails for tall tower

Rails for tall tower

Fit the other rails to the tower frame. Notice the right side of the tower. Here we’re going to install a large slider, so you should remember that you might adjust their location according to the product you use.

Building the stairs for the tall tower

Building the stairs for the tall tower

We also need to frame stairs for the tall tower. There will be a bridge between the tall and short forts and we need the stairs to access the former. Therefore, use 2×4 lumber for the steps and frame. Assemble the frame for the stairs on a level surface with 2 1/2″ screws. Fit the stairs into place, drill pilot holes through the left support and insert 2 1/2″ screws into the steps. Secure the right stringer to the post with 2 1/2″ screws.

Railings 3 - tall tower

Railings 3 – tall tower

Fit 1×4 slats to the rails. Make sure you space the slats as even as possible. Drill pilot holes and insert 1 5/8″ screws to lock the slats to the rails. You can cut a piece of wood to 2 3/8″ and use it as spacer when installing the slats.

Railings 2 - tall tower

Railings 2 – tall tower

Fit the slats to the other side of the tower.

Railings 1 - tall tower

Railings 1 – tall tower

And more slats to install.

Tall tower for outdoor playset

Tall tower for outdoor playset

Fill the holes with wood putty and smooth the surface with 120-220 grit sandpaper. Apply a few coats of paint or stain to the components to protect them from the elements. You can also staple landscape fabric to the inside of the bottom frame and fill it with sand.

 

 

Building the short fort for the playset

Frames for short tower

Frames for short tower

We are going to build the short tower for the playset in the same manner described above. First, build the 2 frames. 1×6 lumber for the bottom frame and 2×4 lumber for the floor frame. Drill pilot holes and assemble everything with 2 1/2″ screws. Align the edges and make sure the corners are right angled.

Assembling the short tower

Assembling the short tower

Attach the 4×4 posts to the frames. Make sure the corners are square and align the edges, before inserting the 3 1/2″ screws. Also, remember we need to anchor the posts to the footings with hardware.

Floor slats - short tower

Floor slats – short tower

Attach the 1×6 slats to the floor frame. Fit a piece of 1/4″ plywood between the slats to create even gaps. Drill pilot holes and insert 2 1/2″ screws to lock the slats into place. Align the slats at both ends before inserting the screws.

Rafters-for-short-tower

Rafters-for-short-tower

Build the rafters for the short tower. Make 45 degree cuts to the 2×4 beams. We will need 1 piece of the 56 1/2″ long rafter and 5 pieces of the 37 1/2″ long rafters. We need the long rafter to hold the swing we are going to build in PART 2.

Rafters for short tower

Rafters for short tower

Join the rafters together in a A frame. Align the edges, drill pilot holes and insert 3 1/2″ screws to lock the to the top of the posts.

Roof slats - short tower

Roof slats – short tower

Fit the 1×6 slats to the top of the fort. Add glue between the slats and leave no gaps between them. Align the slats at both ends. Drill pilot holes and insert 2 1/2″ screws to lock the slats to the rafters.

Rails-for-short-tower

Rails-for-short-tower

Next, we need to attach the supports for the railings. Use 2×4 lumber for the rails. Align the edges, drill pilot holes and insert 2 1/2″ screws to lock them into place tightly.

Balusters 3 - short tower

Balusters 3 – short tower

Fit the 1×4 slats to the rails. Use 1 5/8″ screws to secure the slats into place.

Balusters 2 - short tower

Balusters 2 – short tower

 

Balusters 1 - short tower

Balusters 1 – short tower

 

Short tower - outdoor playhouse

Short tower – outdoor playhouse

Fill the holes with wood putty and smooth the surface with 120-220 grit sandpaper. Apply a few coats of paint or stain to the components to protect them from the elements. You can also staple landscape fabric to the inside of the bottom frame and fill it with sand.

Playset-with-fort-and-slide-plans

Playset-with-fort-and-slide-plans

 

How-to-build-a-large-playset-with-forts-and-slides

How-to-build-a-large-playset-with-forts-and-slides

This is a complex woodworking project, but any person with basic diy skills can get the job done in a few days, using my free set of plans. If you like my project, I recommend you to take a look over the rest of my woodworking plans HERE. See all my playhouse plans HERE. Choose from thousands of free designs and fill your life with DIY joy!

If you want to get PREMIUM PLANS for this project, in a PDF format, please press GET PDF PLANS button bellow. Thank you for the support.

 

 

This woodworking project was about outdoor playhouse with bridge, swing and slides plans. If you want to see more outdoor plans, we recommend you to check out the rest of my step by step projects. LIKE us on Facebook and Google + to be the first that gets out latest projects.

 

Next

 

 

 

EXPLORE MORE IDEAS FOR:

You may also like

1 comment

Jordan -

What size of slides are required for this plan, and where can I purchase?

Reply

Leave a Reply to Jordan Cancel Reply