This step by step diy woodworking project is about backyard pavilion plans. The project features instructions for building a 12×14 wooden pavilion. If you want to create a nice recreation area in your backyard, this simple construction with a neat design is a good option to consider. Make sure you check out the rest of plans to see alternatives and more projects for your garden.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.
Projects made from these plans
Backyard Pavilion Plans
[tabs tab1=”Materials” tab2=”Tools” tab3=”Time”]
- A – 6 pieces of 4×4 lumber – 120″ long POSTS
- B – 4 pieces of 2×6 lumber – 168″ long BEAMS
- C – 8 pieces of 4×4 lumber – 34″ long BRACES
- D – 8 pieces of 2×6 lumber – 147″ long RAFTERS
- E – 2 pieces of 2×4 lumber – 37″ long, 1 piece of 2×6 lumber – 168″ long TOP RIDGE
- F – 16 pieces of 2×4 lumber – 96″ long RAFTERS
- G – 6 pieces of 3/4″ plywood – 48″x95 1/4″ long, 2 pieces – 24″x95 1/4″ long ROOF
- H – 250 sq ft of tar paper, 250 sq ft of asphalt shingles ROOFING
- I – 2 pieces of 1×4 lumber – 168″ long, 4 pieces of 2×4 lumber – 37″ long TRIMS
- 9 pieces of 4×4 lumber – 12′
- 13 pieces of 2×6 lumber- 14′
- 18 piece of 2×4 lumber – 8′
- 2 pieces of 1×4 lumber – 14′
- 7 pieces of 3/4″ plywood – 4’x8′
- 250 sq ft of tar paper
- 250 sq ft of asphalt shingles
- 1 1/4″ screws
- 1 5/8″ screws
- 2 1/2″ screws
- filler, stain
- metal connectors
Building a 12×14 backyard pavilion
The first step of the project is to layout the posts for the pavilion. Use batter boards and string to layout the posts. Measure the diagonals and adjust them until they are perfectly equal. Apply the 3-4-5 rule to each corner to make sure the corners are right-angled.
Build the posts from 4×4 lumber. As you can notice, you need to set the posts 24″ in concrete.
Set the posts into concrete for about 2-3′. Use a post hole digger to make the holes. Set tube forms into the holes and fit the posts into place. Use a spirit level to plumb the posts and lock them temporarily into place with braces. Fill the tube forms with concrete and let it dry out for several days.
Next, attach the 2×6 beams to the top of the posts. Align the edges with attention, make sure the corners are square and check if the beams are perfectly horizontal. Clamp the beams into place tightly.
Drill pilot holes through both the beams and through the posts. Next, insert 7″ carriage bolts to lock the beams to the top of the posts, as shown in the diagram.
If you want to add support to the backyard construction, you should install 4×4 braces to the posts. Cut both ends of the braces at 45 degrees. Smooth the cut edges with sandpaper. Fit the braces to the sides of the pavilion, between the support beams, as shown in the diagram. Align the edges with attention, drill pilot holes and use 3 1/2″ screws to lock them into place.
Build the bottom rafters from 2×6 lumber. Cut both ends of the beams at 30 degrees.
Fit the bottom rafters to the top of the support beams. Place the rafters equally-spaced. Use appropriate metal connectors to lock the rafters to the support beams.
Next, you need to build the supports for the top ridge. Use 2×4 lumber for the supports and make the angle cuts to the top edge.
Afterwards, you need to make a notch to the top of the supports. Mark the cut lines on the supports and get the job done with a jigsaw. Smooth the edges with sandpaper.
Fit the supports to the end bottom rafters. Use a spirit level to check if the supports are plumb. Use plate connectors to lock the supports to the bottom rafters.
Build the top ridge from 2×6 lumber. Fit the beams to the top of the supports, as shown in the plans. Drill pilot holes and insert 3 1/2″ screws to lock the beams to the supports. Make sure the corners are right-angled.
Build braces for the top ridge from 2×4 lumber. Cut both ends of the braces at 45 degrees and lock them into place using 3 1/2″ screws. Drill pilot holes before inserting the screws, to prevent the wood from splitting.
Build the regular rafters for the pavilion from 2×4 lumber. Cut both ends of the rafters at 60 degrees, using a miter saw.
Fit the rafters to the top of the structure. Make sure the rafters are equally-spaced, 24″ on center. Drill pilot holes through the rafters and insert 3 1/2″ screws into the support beams and into the top ridge.
Next, you need to build trims for the front and back gale ends. Mark the cut lines on the 2×4 lumber and get the job done with a circular saw.
Fit the trims to the front and back of the pavilion. Drill pilot holes at both ends of the trims and lock them to the structure using 2 1/2″ screws.
Attach 1×4 slats to the ends of the rafters, to enhance the look of the wooden pavilion. Use 1 5/8″ brad nails to lock the trims into place. Align the edges and leave no gaps between the components.
Attach 3/4″ plywood sheets to the rafters. Align the sheets, making sure the edges are flush. Leave no gaps between the sheets and lock them into place with 1 5/8 screws, every 8″ along the rafters.
Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. Secure the tar paper to the plywood sheets with roofing staples. In addition, cut a 12″ piece for the top ridge. Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under.
This simple pavilion has a neat design, making it a good choice for any property.
If you want, you can easily adjust the size of the pavilion to suit your needs. Fill the holes with wood putty and smooth the surface with sandpaper. Cover the components with paint or stain to protect the components from decay and to enhance the look of the project.
Top Tip: If you live in an area with heavy winters, you should increase the slope of the roof.
This woodworking project was about backyard pavilion plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.