Home 10x16 10×16 Pavilion Plans

10×16 Pavilion Plans

by Ovidiu

 

This step by step diy woodworking project is about a 10×16 outdoor pavilion plans. I have brand new plans for you to build this super sturdy pavilion with a rectangular shape and a gable roof. This pavilion is built on a 6×6 framing and it features a plywood and shingles roofing. Take a look over the rest of our woodworking plans, if you want to get more building inspiration.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.

 

 

Projects made from these plans

Add-image

 

 

10×16 Backyard Pavilion – Free DIY Plans

Building-a-10x16-pavilion

Building-a-10×16-pavilion

 

[tabs tab1=”Materials” tab2=”Tools” tab3=”Time” tab4=”Related Plans”] [tab id=1]

  • A – 6 pieces of 6×6 lumber – 132″ long POSTS
  • B – 2 pieces of 6×6 lumber – 216″ long TOP PLATES
  • C – 3 pieces of 6×6 lumber – 120″ long PLATES
  • D – 12 pieces of 6×6 lumber – 36″ long BRACES
  • D – 3 pieces of 6×6 lumber – 30 1/4″ long, 1 piece – 216″ long, 3 pieces – 34″ long RIDGE BEAM

  • 6 pieces of 6×6 lumber – 12′
  • 3 pieces of 6×6 lumber – 18′
  • 8 pieces of 6×6 lumber – 10′
  • 5″ screws, 8″ screws
  • wood glue, stain/paint
  • post hole digger
  • post anchors
  • beam to post connectors
  • structural screws for connectors
  • strong tie T

[/tab] [tab id=2]

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

[/tab] [tab id=3]

 One day

[/tab][tab id=4]

[/tab][/tabs]

 

 

Trim---Facebook-BoxMake sure you follow me on Facebook to be the first that gets my latest plans and for some other exclusive content. Also, follow me on Pinterest to get many ideas for your backyard from all the internet! Check out my YouTube channel for ! See how you can SUPPORT ME with no extra costs to you. Trim---Facebook-Box-Down

 

 

How to build a 10×16 pavilion

Laying-out-the-posts-for-the-pavilion

Laying-out-the-posts-for-the-pavilion

The first step of the project is to layout the posts for the 10×16 pavilion. Use batter boards and string to determine the location of the posts. Apply the 3-4-5 rule to every corner of the pavilion, so you make sure they are right angled. Moreover measure the diagonals and make sure they are equal. Determining the location for the pavilion is essential, as you have to comply with the local building codes.

Anchoring the posts of the anchor

Anchoring the posts of the anchor

Dig 3′ deep holes into the ground with a post hole digger. Align the holes with attention and then fit form tubes. Fit the 6×6 posts with attention and align them using string. Use a spirit level to plumb the posts and then lock them into place with temporarily braces. Fill the tube forms with concrete and let it dry out for a few days. Setting the pressure treated/cedar posts in concrete is a lot better than using post anchors, as the posts will be locked in the concrete footers. *The materials list is made considering you will set the posts into concrete.

Side plates - 10x16 pavilion

Side plates – 10×16 pavilion

Use 6×6 lumber for the side top plates of the pavilion. Use a circular saw to make the notches to beams, as shown in the diagram. Make parallel cuts inside the marked areas and then remove the excess with a chisel. Smooth the surface with sandpaper.

Top-plates-for-10x16-pavilion-gable-roof

Top-plates-for-10×16-pavilion-gable-roof

Make the rest of the top plates for the pavilion using the diagram above. Mark the cut lines on the beams and then make 2 3/4″ deep parallel cuts. Remove the excess material with a chisel and a hammer.

Fitting the top plates

Fitting the top plates

Fit the top plates to the top of the posts. Plumb the posts with a spirit level and make sure the plates are horizontal. Check if the corners are square and align the edges with attention. Drill pilot holes through the plates and insert 8″ screws into the top of the posts.

Fitting the braces to frame of the 10x16 pavilion

Fitting the braces to frame of the 10×16 pavilion

Use 6×6 lumber for the braces. Double check if the posts are plumb and if the corners are square. Cut both ends of the braces at 45 degrees and then secure them into place with 5″ screws, after drilling pilot holes. These braces will really enhance the rigidity of the pavilion, so make sure you don’t take shortcuts and install them properly.

Fitting-the-ridge-beam---gable-pavilion

Fitting-the-ridge-beam—gable-pavilion

Use 6×6 lumber for the ridge beam supports and for the beam itself. Use a spirit level to plumb the supports and secure them into place with corner brackets. Fit the top ridge into place and use corner brackets to lock them into place, as well. Check if the corners are square and align the edges with attention. Use 8″ screws to reinforce the joists.

Top ridge braces

Top ridge braces

Last but not least, you need to attach the 6×6 braces to the structure of the pavilion, so you can enhance the rigidity. Cut both both ends of the braces at 45 degrees and then secure them into place tightly, with 5″ screws.

How-to-build-a-10x16-gable-pavilion

How-to-build-a-10×16-gable-pavilion

You should check out PART 2 of the 16×24 pavilion plans, so you learn how to build the gable roof.

10x16 pavilion plans - Side view

10×16 pavilion plans – Side view

Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-220 grit sandpaper and remove the residues with a damp cloth.

Top Tip: Apply a few coats of paint or stain to the components, to enhance the look of the project. Make sure you take a look over the rest of my pergola/gazebo/pavilion plans HERE. See all my free woodworking plans (over 1000) HERE.

If you want to get PREMIUM PLANS for this project, in a PDF format, please press GET PDF PLANS button bellow. Thank you for the support.

 

 

This woodworking project was about 10×16 outdoor pavilion plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result. Feel free to SHARE my plans with your friends.

 

Next

 

 

 

EXPLORE MORE IDEAS FOR:

You may also like

4 comments

Hom -

Can this be built using 4×4 instead of 6×6 ?

Reply
Ovidiu -

Yes, of course.

Reply
Joe Mazoway -

Looking for plans for a 16×24 pavilion

Reply
Zeena -

Looking for a plan for 30wide x 16long

Reply

Leave a Comment