Home Arbor Peaked Arbor Plans

Peaked Arbor Plans

by Ovidiu

 

This step by step diy woodworking project is about peaked arbor plans. This detailed article features instructions and complete diagrams about building a wooden arbor with a peaked roof. Adjust the design of the structure to suit your needs and budget. This project requires basic tools and materials, so that any person with basic skills can get the job done in less than a week.

Work with good judgement and don’t forget to take a look over the rest of the related plans, as there are many designs and woodworking projects to select from. Work with attention and don’t forget that a good planning will save you from many issues and it will keep the costs within the total budget. Invest in high quality materials, such as pine, redwood or cedar. Drill pocket holes before inserting the galvanized screws, to prevent the wood from splitting. See all my Premium Plans HERE.

 

 

Projects made from these plans

Add-image

 

 

It’s that simple to build a garden arbor!

 

 

Peaked arbor plans

Building a peaked roof arbor

Building a peaked roof arbor

 

Cut & Shopping Lists

  • A – 4 pieces of 4×4 lumber – 86″ long LEGS
  • B – 1 piece of 2×2 lumber – 66 1/2″ long, 8 pieces – 24″ long 2xTRELLIS
  • C – 4 piece of 2×6 lumber – 36″ long SUPPORT BEAMS
  • D – 2 pieces of 2×6 lumber – 74″ long BEAMS
  • E – 4 pieces of 2×4 lumber – 42 1/2″ long, 4 pieces – 16 3/4″ long, 2 pieces – 25″ long RAFTERS
  • F – 10 pieces of 2×2 lumber – 27″ long SLATS

Tools

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

Time

 One day

Related

 

 

Trim---Facebook-BoxMake sure you follow us on Facebook to be the first that gets our latest plans and for some other exclusive content. Also, follow us on Pinterest to get many ideas for your backyard from all the internet! See how you can Support Us with no extra costs to you. Trim---Facebook-Box-Down

 

 

Building a peaked roof arbor

Laying out the arbor

Laying out the arbor

The first step of the project is to lay out the posts for the arbor with a peaked roof. Use batter boards to lay out the arbor. Make sure the corners are right-angled by applying the 3-4-5 rule to each corner.

Anchoring the post into concrete

Anchoring the post into concrete

There are several ways to lock the posts into place. Therefore, you could dig holes in the ground and set the posts into concrete, or you could use post anchors. Nevertheless, taking into account the height of the construction, we recommend you to lock the posts into concrete.

Level the posts with a spirit level and secure them temporarily with 2×4 braces. Make sure the top of the posts are at the same level, otherwise the structure of the arbor won’t be sturdy enough.

Building the side trellis

Building the side trellis

Use 2×2 lumber to build the side trellis. Cut the components at the right dimensions and lay them on a horizontal surface. Drill pilot holes through the vertical component and insert 2 1/2″ screws into the horizontal ones.

Fitting the trellis

Fitting the trellis

Next, attach the trellis to the posts and lock them into place using 2 1/2″ screws.

Building the support beams

Building the support beams

Use 2×6 lumber to build the beams. Mark the cut lines on the beams and get the job done with a circular saw. Use a jigsaw to make the curved cuts. Smooth the edges with fine-grit sandpaper.

Fitting the support beams

Fitting the support beams

The next step of the project is to fit the support beams to the top of the posts. Clamp the beams to the posts and drill pilot holes through both the posts and through the beams. Insert 7″ carriage bolts to lock everything together tightly.

Building the beams

Building the beams

Build the long beams out of 2×6 lumber. Mark the cut lines on the beams and get the job done with a circular saw. Make parallel cuts inside the notches and clean the recess with a chisel.

Fitting the beams

Fitting the beams

Fit the beams to the structure of the arbor, as described in the diagram. Drill pilot holes through the beams and lock them to the posts and to the support beams by inserting 5″ screws.

Building the rafters

Building the rafters

Build the rafters for the arbor out of 2×4 lumber. Cut both ends of the components at 45 degrees. Fit the rafters to the structure, drill pilot holes and lock them into place using 3 1/2″ screws. Leave no gaps between the components.

Building the roof trims

Building the roof trims

Build some decorative trims for the peaked roof of the arbor. Cut the trims and the right dimensions and angles before locking them into place with 2 1/2″ screws. Smooth the edges with fine-grit sandpaper.

Fitting the roof trims

Fitting the roof trims

Lock the trims to the structure, making sure the joints are rigid and there are no gaps between the components.

Fitting the top slats

Fitting the top slats

Fit 2×2 slats to the top of the peaked roof, in order to enhance the look of the arbor. Place the slats equally-spaced and lock them to the rafters using 2 1/2″ screws.

Peaked arbor plans

Peaked arbor plans

One of the last steps of the woodworking project is to take care of the finishing touches. Therefore, fill the pilot holes with wood putty and smooth the surface with 120-grit sandpaper.

Top Tip: If you want to enhance the look of the project and to protect the wooden arbor from decay, we recommend you to cover the components with paint or stain.

 

 

This woodworking project was about peaked arbor plans free. If you want to see more outdoor plans, we recommend you to check out the rest of our step by step projects. LIKE us on Facebook and Google + to be the first that gets out latest projects and to hep us keep adding free woodworking plans for you.

 

 

EXPLORE MORE IDEAS FOR:

You may also like

5 comments

Paul -

Re instructions for peaked Arbour . It says use 7in carriage bolts to hold the main beams to the posts but the posts are 4 in and the beams are 2 in thick making a total of 8in I just wandering if I am missing something and also would u recommend two bolts each side or four.
Thanks.

Reply
Paul -

Re last comment my email address is –

I unfortunately missed out the e in blueyonder

Reply
Ovidiu -

4×4 lumber is actually 3 1/2″x3 1/2″ and 2x4s are actually 1 1/2″x3 1/2″ See more at: http://myoutdoorplans.com/imperial-to-metric-conversion/

Reply
paul -

Thank you very much for responding to my question .
Jut one more : What do you recommend the height of the posts from ground level to the main beams thanks.

Reply
Ovidiu -

My recommendation is the plan. That is my vision regarding the project.

Reply

Leave a Reply to paul Cancel Reply