This step by step diy project is about 5×12 pent shed roof plans. This is PART 2 of the free 5×12 lean shed plans, where I show you how to build the lean to roof and how to attach the siding sheets. Make sure you check the local codes and make adjustments to the plans, if required. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look.
Projects made from these plans
5×12 Pent Shed Roof Plans
- E – 2 pieces of 2×4 lumber – 144″ long, 12 pieces – 15 3/4″ long TOP WALL
- H – 2 pieces of T1-11 siding – 23 3/4″x48″ long, 2 pieces – 7 3/4″x12″ long, 3 pieces – 20 1/4″x48″ long SIDING
- I – 11 pieces of 2×4 lumber – 84″ long RAFTERS
- J – 1 piece of 3/4″ plywood – 48″x83″ long, 1 piece – 48″x81″ long, 1 piece – 36″x83″ long, 1 piece – 36″x57″ long, 1 piece – 36″x24″ long ROOF
- K – 2 pieces of 1×6 lumber – 84″ long, 1 piece of 1×6 lumber – 165 1/2″ long TRIMS
- L – 2 pieces of 2×4 lumber – 84″ long, 5 pieces of 2×4 lumber – 6 1/2″ long 2xOVERHANG
- M – 120 sq ft of tar paper, 100 sq ft of asphalt shingles ROOFING
- 2 pieces of 5/8″ T1-11 – 4’x8′
- 2 pieces of 2×4 lumber – 12′
- 18 pieces of 2×4 lumber – 8′
- 4 pieces of 3/4″ plywood – 4’x8′
- 2 pieces of 1×6 lumber – 8′
- 2 pieces of 1×6 lumber – 14′
- 100 sq ft of tar paper, 100 sq ft of asphalt shingles
- tar paper
- 6d nails, 2 1/2″ screws, 3 1/2″ screws
- wood filler , wood glue, stain/paint
Building a 5×12 pent shed roof
The first step of the project is to build the top frame for the back of the shed. Cut the components from 2×4 lumber at the dimensions shown in the diagram. Drill pilot holes through the plates and insert 3 1/2″ screws into the studs. Place the studs every 16″ on center, for a professional result.
Fit the wall frame to the top of the back wall. Align the edges with attention and plumb it with a spirit level. Drill pilot holes through the bottom plates and insert 3 1/2″ screws into the wall.
Next, fit the T1-11 siding panels to the top of the side wall. Align the edges with attention and insert 2″ nails, every 8″ along the framing.
Use 2×4 lumber for the rafters. Mark the cut lines on the boards and then get the job done with a circular saw. Take accurate measurements before making the cuts, otherwise you won’t be able to fit them into place tightly.
Fit the rafters to the top of the shed, every 16″ on center. Use rafter ties to lock the rafters into place tightly.
Mark the cut lines on the T1-11 siding panels and then get the job done with a circular saw. Fit the T1-11 siding sheets to the lean to sides of the shed. Align the edges and insert 6-8d nails, every 8″ along the framing.
Use 2×4 lumber for the side overhangs. Cut the components at the right dimensions and then lock them together tightly with 2 1/2″ screws. Make sure the edges are flush and check if the corners are square.
Fit the overhangs to the sides of the shed and align the edges with attention. Drill pilot holes and insert 3 1/2″ screws to lock them into place tightly.
Fit the 3/4″ plywood sheets to the roof of the shed. Align the edges with attention and insert 1 5/8″ screws, every 8″ along the framing. Leave no gaps between the sheets for a professional result.
Fit 1×6 trims to the sides of the roof. Fit 1×6 trims to the front and back of the shed roof. Align the edges with attention, drill pilot holes and insert 3 1/2″ screws.
Cover the roof with tar paper and then install the asphalt shingles. Make sure you also install the appropriate drip edges, so you can seal the shed roof. Read the manufacturer’s instructions for a tight fit.
I have lots of other shed projects on the site so I recommend you to browse through all alternatives before starting the building project. See all my shed projects HERE. Moreover, check out PART 1 of the shed, so you learn how to build the frame of the shed. Check out PART 3 of the shed, so you learn how to build the double doors.
This woodworking project was about 5×12 lean to shed roof plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.