Home Shed 12×16 Run in Shed Roof Plans

12×16 Run in Shed Roof Plans

by Ovidiu

 

This step by step diy woodworking project is about 12×16 run in shed roof plans. This article is PART 2 of the run in shed project, where I show you how to frame the lean to roof and how to fit the decorative trims. Make sure you check out the rest of plans to see alternatives and more projects for your garden.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.

 

 

Projects made from these plans

Add-image

 

 

12×16 Run in Shed Roof Plans

Building-a-12x16-run-in-shed

Building-a-12×16-run-in-shed

 

Cut & Shopping Lists

  • D – 2 pieces of T1-11 siding – 48″x48″ long, 2 pieces – 38 3/4″x48″ long, 2 pieces – 21 1/4″x48″ long, 2 pieces – 24″x96″ long, 2 pieces – 48″x51 1/4″ long, 2 pieces – 13 1/2″x48″ long SIDING
  • E – 13 pieces of 2×6 lumber – 192″ long, 2 pieces of 2×4 lumber – 16″ long, 2 pieces – 33 1/2″ long RAFTERS
  • F – 2 pieces of 2×6 lumber – 192″ long, 9 pieces – 8 1/4″ long 2xOVERHANG
  • G – 4 pieces of 3/4″ plywood – 12″x96″ long, 6 pieces of 3/4″ plywood – 48″x96″ long, 4 pieces – 48″x48″ long ROOF SHEETS
  • H – 300 sq ft of tar paper, 300 sq ft of asphalt shingles ROOFING
  • I – 4 pieces of 1×4 lumber – 144″ long, 2 pieces – 96″ long, 2 pieces – 94 3/4″ long TRIMS
  • J – 2 pieces of 1×8 lumber – 218 3/4″ long, 2 pieces – 192″ long    TRIMS

Tools

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

Time

 One day

 

 

Building a 12×16 shed roof plans

Rafters

Rafters

Build the rafters from 2×64 lumber. Make notches to the rafters, using the information from the diagram. Smooth the recesses with sandpaper.

Fitting-the-rafters

Fitting-the-rafters

Fit the rafters to the top of the shelter. Drill pilot holes and lock the rafters to the structure with screws and rafter ties. Place the rafters every 16″ on center.

supports

supports

Use 2×4 lumber for the side lean to roof supports. Make the angle cuts with a miter saw and then lock them into place tightly with screws.

Side panels

Side panels

Attach 4’x8′ T1-11 siding to the back wall of the shelter. Use 6d brad nails to lock the sheets into place tightly. Insert the nails every 8″ along the wall framing.

Front wall siding panels

Front wall siding panels

Cut the sheets before attaching them to the front of the shed. Align the edges with attention and leave no gaps between the sheets for a professional result.

Building the overhagns

Building the overhangs

Continue the project by assembling the side roof overhangs. Therefore, cut the components from 2×6 lumber. Drill pilot holes through the rafters and insert 3 1/2″ screws into the blockings. Align the edges with attention before inserting the screws.

Fitting the overhangs

Fitting the overhangs

Fit the overhangs to the sides of the shed. Align the edges with attention, drill pilot holes and insert 3 1/2″ screws to lock them into place tightly.

Roof-sheets

Roof-sheets

Cut the 3/4″ plywood sheets at the right dimensions, as shown in the diagram. Align the edged with attention and leave no gaps between the sheets. Insert 1 5/8″ screws, every 8″ along the framing.

Roof trims

Roof trims

Fit the 1×8 trims to the sides, to the front and to the back of the shed. Cut the components at the right dimensions and then align them into place with attention. Drill pilot holes and then insert 2″ nails, every 8″ along the framing.

Fitting the roofing

Fitting the roofing

Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. Secure the tar paper to the plywood sheets with roofing staples. In addition, cut a 12″ piece for the top ridge. Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under.

Back wall trims

Back wall trims

Fit the 1×4 trims to the back of the shed. Align the edges with attention and insert 2″ nails to lock them into place tightly.

Side trims

Side trims

Fit the trims to the sides of the shed. Make the angle cuts to the trims so you can fit them into place tightly.

Front wall trims

Front wall trims

Fit the trims to the front of the shed. Align the edges flush and insert the 6d nails, every 8″.

Free 12x16 run in shed plans - Front view

Free 12×16 run in shed plans – Front view

This run in shed is easy to build and it is very sturdy.

Free 12x16 run in shed plans - Back view

Free 12×16 run in shed plans – Back view

Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-200 grit sandpaper and remove the residues with a damp cloth.

Top Tip: Check out PART 1 of the project, to learn how to build the frame for the  10×14 run in shed.

 

 

This woodworking project was about 12×16 run in shelter plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

 

Previous

 

 

 

EXPLORE MORE IDEAS FOR:

You may also like

Leave a Comment