Home 20x30 20×30 Pavilion Plans

20×30 Pavilion Plans

by Ovidiu

 

This step by step diy woodworking project is about a 20×30 outdoor pavilion plans. I had a request for a large pavilion with a simple design, so I’ve come up with this design. This small pavilion has a gable roof and it is super simple to build. Make sure you take a look over the local building codes, so you comply with the regulations. Take a look over the rest of our woodworking plans, if you want to get more building inspiration.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.

 

 

Projects made from these plans

Add-image

 

 

20×30 Pavilion Plans

Building-a-20x30-pavilion

Building-a-20×30-pavilion

 

Cut List

  • A – 12 pieces of 6×6 lumber – 132″ long POSTS
  • B – 4 pieces of 6×6 lumber – 206 3/4″ long, 2 pieces – 240″ long TOP PLATES
  • C – 16 pieces of 6×6 lumber – 48″ long, 2 pieces – 60″ long BRACES
  • D – 2 pieces of 6×6 lumber – 68 1/4″ long, 1 piece – 408″ long TOP RIDGE

Shopping List

Tools

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

Time

One week

Related

 

 

Trim---Facebook-BoxMake sure you follow us on Facebook to be the first that gets our latest plans and for some other exclusive content. Also, follow us on Pinterest to get many ideas for your backyard from all the internet! Check out our YouTube channel! See how you can Support Us with no extra costs to you. Trim---Facebook-Box-Down

 

 

How to build a 20×30 pavilion

Laying-out-the-posts

Laying-out-the-posts

The first step of the project is to layout the posts for the 20×30 pavilion. Use batter boards and string to determine the location of the posts. Apply the 3-4-5 rule to every corner of the pavilion, so you make sure they are right angled. Moreover measure the diagonals and make sure they are equal. Determining the location for the pavilion is essential, as you have to comply with the local building codes. Make sure the surface is level and remove the vegetation layer.

Posts

Posts

Level the surface with attention. Remove the vegetation layer, as well. Dig 3′ deep holes into the ground with a post hole digger. Align the holes with attention and then fit form tubes. Fit the 6×6 posts with attention and align them using string. Use a spirit level to plumb the posts and then lock them into place with temporarily braces. Fill the tube forms with concrete and let it dry out for a few days.

Side-top-beams

Side-top-beams

Use 6×6 lumber for the top plates of the pavilion. As you can notice in the plans, you have to make notches to the beams, so you can join then them together. Mark the areas and then make parallel cuts with a circular saw set at a depth of 2 3/4″. Remove the excess material with chisel and smooth the recess with sandpaper.

Top-beams

Top-beams

Repeat the process for the front and back top plates of the pavilion. Make the notches and remove the excess.

Fitting the top beams

Fitting the top beams

Fit the rails to the sides of the pavilion. Align the edges flush, making sure the corners are square, drill pilot holes and insert 5 1/2″ screws.

 

Framing the roof supports

Top ridge

Top ridge

Continue the project by building the ridge beam. Make recesses to the beam, so you can fit it into place properly.

Fitting the top ridge

Fitting the top ridge

Fit the 6×6 supports to the front and back of the pavilion. Plumb the support with a spirit level and make sure the corners are square.

Front and back braces

Front and back braces

Build the braces from 6×6 lumber. Cut both ends of the braces at 45 degrees and then fit them into place tightly. Leave no gaps between the components, drill pilot holes and insert 5 1/2″ screws.

Fitting the braces

Fitting the braces

Fit the 6×6 braces to secure the ridge beam.

Fitting the top ridge braces

Fitting the top ridge braces

 

Fit the 4×4 braces to the top ridge. Make sure the corners are square before fitting the braces into place.

 

Finishing touches

20x30 Pavilion Plans

20×30 Pavilion Plans

You should check out PART 2 of the 20×30 pavilion plans, so you learn how to build the gable roof.

20x30 Pavilion Plans Free

20×30 Pavilion Plans Free

Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-220 grit sandpaper and remove the residues with a damp cloth.

Top Tip: Apply a few coats of paint or stain to the components, to enhance the look of the project. PREMIUM PLANS available for a 20×30 gable pavilion in the SHOP.

If you want to get PREMIUM PLANS for this project, in a PDF format, please press GET PDF PLANS button bellow. Thank you for the support.

 

 

This woodworking project was about 20×30 outdoor pavilion plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

 

Next

 

 

 

EXPLORE MORE IDEAS FOR:

You may also like

10 comments

PZ -

We are reviewing your 20×30 pavilion. Although we feel your design is excellent, the availability of 6x6x20 and 6x6x34 treated lumber is non-existent. We are having to re-engineer with shorter timbers and sandwich them together.

Reply
Ovidiu -

Yes, that is an option. You can usually join pieces together if there are not available in longer sizes.

Reply
Kristi -

Do you know what the snow load of the roof would be? I love this plan and would like to build it on my property in the mountains.

Reply
Ovidiu -

I don’t know. The safest bet would be to read the local codes and modify my plans accordingly.

Reply
Juan Rodriguez -

I am not an engineer or a professional builder. I have built projects like this in the past only as a hobby or for personal satisfaction. I really enjoy looking at your plans and am actually getting ready to build a pavilion using your designs. My question about this 20 x 30 is not meant as an insult or to discredit anyone, so please don’t interpret it like that.
Is using a 6 x 6 x 34 ft as a ridge beam without center support a good idea? That’s a huge piece of wood, it’s own weight alone could potentially be enough to cause sagging over time.

Thank you.

Reply
Michael Berner -

You brought up a very good point. To remedy that concern would be to add a cross brace in the center on the top plate, below the Ridge Beam in the middle & support it just like the front & back.

Reply
Gerald Phillips -

Exactly what I was looking for as far as size but would you happen to have plans for same size but with a double hip roof

Reply
Ovidiu -

I don’t have plans for that yet.

Reply
prius -

i need plan to build pavilion in church place with 6″ concrete slab.. Can you please advice where to get one
thank you

Reply
Jeff -

Do you have premium plans available for this project? I looked on your premium sit but wasn’t able to find the plans for this project.

Reply

Leave a Reply to Ovidiu Cancel Reply