Home Hunting Building the Hunting Blind Roof

Building the Hunting Blind Roof

by Ovidiu

 

This step by step diy project is about 4×6 deer blind roof plans. This is PART 2 of the deer blind project, where I show you how to build the roof and the dack door. Make sure you pay attention to the instructions and make adjustments if necessary. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day. See all my Premium Plans HERE.

 

 

Projects made from these plans

Add-image

 

 

Building the Hunting Blind Roof

Building-a-4x6-deer-blind

Building-a-4×6-deer-blind

 

Cut & Shopping Lists

  • F – 3 piece of 3/4″ plywood – 48″x80 1/2 long, 1 piece – 24″x80 1/2″ long, 1 piece – 48″x76 1/2″ long, 1 piece – 24″x76 1/2″ long WALLS
  • G – 2 pieces of 3/4″ plywood – 14″x20 1/2″ long, 2 pieces – 14″x44 1/2″ long, 1 piece – 14″x38″ long, 1 piece – 14″x14″ long BLINDS
  • H – 6 pieces of 2×6 lumber – 46 1/2″ long, 1 piece – 72″ long RAFTERS
  • I – 1 piece of 3/4″ plywood – 48″x80″ long ROOF
  • J – 40 sq ft of tar paper, 40 sq ft of asphalt shingles ROOFING
  • K – 2 pieces of 2×2 lumber – 69″ long, 2 pieces – 22 1/2″ long, 1 piece – 19 1/2″ long, 1 piece – 22 1/2″x72″ long DOOR

Tools

 Hammer, Tape measure, Framing square, Level

 Miter saw, Drill machinery, Screwdriver, Sander

 Safety Gloves, Safety Glasses

Time

 One day

Related

 

 

Trim---Facebook-BoxMake sure you follow me on Facebook to be the first that gets our latest plans and for some other exclusive content. Also, follow me on Pinterest to get many ideas for your backyard from all the internet! Check out our YouTube channel! See how you can Support  Me with no extra costs to you. Trim---Facebook-Box-Down

 

 

How to build a deer blind roof

Building-the-rafters

Building-the-rafters

The first step of the project is to build the rafters for the deer blinds. Mark the cut lines on the beams and get the job done with a circular saw. Smooth the edges with sandpaper.

Fitting-the-rafters

Fitting-the-rafters

Fit the rafters to the top of the deer stand and place them every 16″ on center. Fit a 2×6 beam to one side of the deer stand. Drill pilot holes and insert screws so u can lock the beam and the rafters to the top plates.

Side walls

Side walls

Use 3/4″ plywood for the side walls. Mark the cut lines on the sheets and get the job done with a saw.

Front and back wall panels

Front and back wall panels

Cut the front and back walls for the deer blind from 3/4″ plywood using the pattern described in the diagram. Mark the cut lines and then get the job done with a saw.

Fitting the exterior walls

Fitting the exterior walls

Fit the wall panels to the exterior of the deer blind and then secure them into place with 1 5/8″ screws, every 8″ along the framing.

Fitting the roof shee

Fitting the roof sheet

Fit the 3/4″ plywood sheet to the top of the deer stand. Center the sheet to the framing and then insert 1 5/8″ screws into the rafters, so you can lock the plywood panel into place.

Fitting the roofing

Fitting the roofing

Cover the roof of the deer blind with tar paper and then install asphalt shingles. Fit nice drip edges to the four edges of the roof.

Building the door

Building the door

Build the door frame from 2×2 lumber. Drill pilot holes and insert 2 1/2″ screws to build the door frame. Then attach the panel that you have cut out in the previous steps. Align the edges flush and insert 1 5/8″ screws.

Fitting the door

Fitting the door

Fit the door to the opening and lock it into place with hinges. Install a latch to lock the door into place tightly. Fit the panel to the window opening. Use hinges to secure it into place.

Side wall blinds

Side wall blinds

Fit the plywood blinds to the sides of the deer blind, as well.

Back wall blinds

Back wall blinds

Fit the blinds to the front of the hunting stand.

Deer stand plans 4x6

Deer stand plans 4×6

Remember that you need to apply a few coats of protective paint to the shelter, so you both make it low key and protect the components from decay. Take a look over PART 1 of the 4×6 deer blind project, where I show you how to build the floor and the wall frames.

 

 

This woodworking project was about 4×6 deer blind roof plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

 

Previous

 

 

 

EXPLORE MORE IDEAS FOR:

You may also like

5 comments

Cory -

How do you get these windows to stay up? My stand will be elevated six feet and I’ll be unable to hook these on the outside. Thanks

Reply
Ovidiu -

You can use string to pull them up. Drill a pilot holes through the wall above the windows and insert the string inside the stand.

Reply
justin -

does the bottom section of the material list account fo the total amount of material or is it additional material?

Reply
Ovidiu -

The bottom is the materials list. The top is the cut list.

Reply
efs -

how much would all of this cost

Reply

Leave a Reply to Ovidiu Cancel Reply