This step by step diy project is about 12×24 carport with hip roof plans. I have designed this carport with a hip roof so you can build a shelter for your car and match the style of your elegant home. You can easily convert this to an outdoor pavilion, as it is perfect for backyard fun. Make sure you read the local building codes before starting the project, so you get aware of the legal requirements and make the necessarily adjustments. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.
Projects made from these plans
1 Car Carport with Hip Roof Plans
- A – 8 pieces of 6×6 lumber – 8′ long POSTS
- B – 2 pieces of 6×6 lumber – 24′ long, 4 pieces – 12′ long SUPPORT BEAMS
- C – 16 piece of 6×6 lumber – 36″ long BRACES
- D – 1 piece of 6×6 lumber – 145 1/2″ long, 1 piece of 2×8 lumber – 145 1/2″ long, 3 pieces of 2×6 lumber – 32″ long, 4 pieces – 30″ long RIDGE BEAM
- PART 1: 12×24 Hip Roof Carport Plans
- PART 2: 12×24 Carport Hip Roof Plans
12×24 Hip Roof carport plans
The first step of the project is to lay out the carport in a professional manner. Build batter boards and use string to layout everything in a professional manner. Apply the 3-4-5 rule to every corner and make sure the diagonal are equal, otherwise the corners won’t be square. Select the location for the carport with attention, making sure it complies with the local codes. Get a building permit if needed. Level the surface with attention, removing the vegetation layer.
You need to set the posts in concrete (about 3-6′ deep – make sure you read the local building codes for accurate information) or use anchors. Use a post hole digger to make the holes. Pour a 2″ layer of concrete on the bottom of the holes so you level them. Fit the tube forms and then the 6×6 posts / fit the anchors. Use a spirit level to make sure the posts are plumb and then secure them temporarily into place with braces. Fill the tubes with concrete and let it dry out as shown on the bags. Make sure the top of the posts are level.
Use 6×6 lumber for the plates that go on top of the posts. Use a circular saw to make the notches, so you can join them together. Make parallel cuts inside the marked areas and then remove the excess with a hammer and a chisel.
Fit the 6×6 plates to the sides of the carport. Align the edges with attention and make sure the corners are square. Drill pilot holes through the plates and insert 8″ screws into the top of the posts.
Use 6×6 lumber for the braces. Make 45 degree cuts to both ends of the braces, using a miter saw.
Fit the braces to the carport, as shown in the diagram. Plumb the posts with a spirit level and make sure the corners are square. Fit the braces into place, drill pilot holes and insert 4 1/2″ screws to lock them into place tightly.
Continue the project by cutting the support beams for the top ridge. Use a circular saw to make the notches, as shown in the diagram.
Fit the plates to the front and back of the carport. Use a spirit level to make sure the plates are perfectly horizontal, before locking them into place with screws. Drill pilot holes and insert 8″ screws to lock them into place tightly.
Cut the beam that holds the middle plates together.
Fit the beam to the carport and align the edges with attention. Drill pilot holes and insert 3 1/2″ screws to lock them into place tightly. Make sure the corners are square and align the edges flush.
Use 2×6 lumber for the ridge beam and for the supports. Drill pocket holes at both ends of the supports and center them to the plates. Use 2 1/2″ screws to lock them into place tightly. Make sure the supports are plumb before attaching the ridge beam. Insert 2 1/2″ screws to secure the beam into place tightly.
Use 2×6 lumber for the braces. Make 45 degree cuts to both ends of the braces, drill pocket holes and lock them into place with 2 1/2″ screws.
I recommend you to take a look over PART 2 of the project, where I show you how to build the hip roof.
This carport with a hip roof is suitable for a car. The roof structure is strong enough for winds and snow, but I recommend you to read the local codes and make modifications, if necessary.
This woodworking project was about 12×24 carport with hip roof plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.